All issues

The article proposes a model for assessing the potential strength of a composite material based on modern fibers with brittle fracture.

Materials consisting of parallel cylindrical fibers that are quasi-statically stretched in one direction are simulated. It is assumed that the sample is not less than 100 pieces, which corresponds to almost significant cases. It is known that the fibers have a distribution of ultimate deformation in the sample and are not destroyed at the same moment. Usually the distribution of their properties is described by the Weibull–Gnedenko statistical distribution. To simulate the strength of the composite, a model of fiber breaks accumulation is used. It is assumed that the fibers united by the polymer matrix are crushed to twice the inefficient length — the distance at which the stresses increase from the end of the broken fiber to the middle one. However, this model greatly overestimates the strength of composites with brittle fibers. For example, carbon and glass fibers are destroyed in this way.

In some cases, earlier attempts were made to take into account the stress concentration near the broken fiber (Hedgepest model, Ermolenko model, shear analysis), but such models either required a lot of initial data or did not coincide with the experiment. In addition, such models idealize the packing of fibers in the composite to the regular hexagonal packing.

The model combines the shear analysis approach to stress distribution near the destroyed fiber and the statistical approach of fiber strength based on the Weibull–Gnedenko distribution, while introducing a number of assumptions that simplify the calculation without loss of accuracy.

It is assumed that the stress concentration on the adjacent fiber increases the probability of its destruction in accordance with the Weibull distribution, and the number of such fibers with an increased probability of destruction is directly related to the number already destroyed before. All initial data can be obtained from simple experiments. It is shown that accounting for redistribution only for the nearest fibers gives an accurate forecast.

This allowed a complete calculation of the strength of the composite. The experimental data obtained by us on carbon fibers, glass fibers and model composites based on them (CFRP, GFRP), confirm some of the conclusions of the model.

This article discusses the mechanical properties of carbon nanotube (CNT)-reinforced platinum under uniaxial tensile loading using the molecular dynamics method. A review of current computational and experimental studies on the use of carbon nanotube-reinforced composites from a structural point of view. However, quantitative and qualitative studies of CNTs to improve the properties of composites are still rare. Composite selection is a promising application for platinum alloys in many cases where they may be subjected to mechanical stress, including in biocompatibility sources. Pt-reinforced with CNTs may have additional possibilities for implantation of the implant and at the same time obtain the required mechanical characteristics.

The structure of the composite is composed of a Pt crystal with a face-centered cubic lattice with a constant of 3.92 Å and a carbon nanotube. The Pt matrix has the shape of a cube with dimensions of $43.1541 Å \times 43.1541 Å \times 43.1541 Å$. The hole size in the average platinum dimension is the radius of the carbon nanotube of the «zigzag» type (8,0), which is 2.6 Å. A carbon nanotube is placed in a hole with a radius of 4.2 Å. At such parameters, the maximum energy level was mutually observed. The model under consideration is contained in 320 atomic bombs and 5181 atomic platinum. The volume fraction of deaths in the Pt-C composite is 5.8%. At the first stage of the study, the strain rate was analyzed for stress-strain and energy change during uniaxial action on the Pt-C composite.

Analysis of the strain rate study showed that the consumption yield strength increases with high strain rate, and the elasticity has increased density with decreasing strain rate. This work also increased by 40% for Pt-C, the elasticity of the composite decreased by 42.3%. In general, fracture processes are considered in detail, including plastic deformation on an atomistic scale.

Superplastic forming of Ni and Ti based alloys is widely used in aerospace industry. The main advantage of using the effect of superplasticity in sheet metal forming processes is a feasibility of forming materials with a high amount of plastic strain in conditions of prevailing tensile stresses. This article is dedicated to study commercial FEM software SFTC DEFORM application for prediction thickness deviation during low temperature superplastic forming of UFG Ti-6-4 alloy. Experimentally, thickness deviation during superplastic forming can be observed in the local area of plastic deformation and this process is aggravated by local softening of the metal and this is stipulated by microstructure coarsening. The theoretical model was prepared to analyze experimentally observed metal flow. Two approaches have been used for that. The first one is the using of integrated creep rheology model in DEFORM. As superplastic effect is observed only in materials with fine and ultrafine grain sizes the second approach is carried out using own user procedures for rheology model which is based on microstructure evolution equations. These equations have been implemented into DEFORM via Fortran user’s solver subroutines. Using of FEM simulation for this type of forming allows tracking a strain rate in different parts of a workpiece during a process, which is crucial for maintaining the superplastic conditions. Comparison of these approaches allows us to make conclusions about effect of microstructure evolution on metal flow during superplastic deformation. The results of the FEM analysis and theoretical conclusions have been approved by results of the conducted Erichsen test. The main issues of this study are as follows: a) the DEFORM software allows an engineer to predict formation of metal shape under the condition of low-temperature superplasticity; b) in order to augment the accuracy of the prediction of local deformations, the effect of the microstructure state of an alloy having sub-microcristalline structure should be taken into account in the course of calculations in the DEFORM software.