All issues

The study of the physiological and pathophysiological processes in the cardiovascular system is one of the important contemporary issues, which is addressed in many works. In this work, several approaches to the mathematical modelling of the blood flow are considered. They are based on the spatial order reduction and/or use a steady-state approach. Attention is paid to the discussion of the assumptions and suggestions, which are limiting the scope of such models. Some typical mathematical formulations are considered together with the brief review of their numerical implementation. In the first part, we discuss the models, which are based on the full spatial order reduction and/or use a steady-state approach. One of the most popular approaches exploits the analogy between the flow of the viscous fluid in the elastic tubes and the current in the electrical circuit. Such models can be used as an individual tool. They also used for the formulation of the boundary conditions in the models using one dimensional (1D) and three dimensional (3D) spatial coordinates. The use of the dynamical compartment models allows describing haemodynamics over an extended period (by order of tens of cardiac cycles and more). Then, the steady-state models are considered. They may use either total spatial reduction or two dimensional (2D) spatial coordinates. This approach is used for simulation the blood flow in the region of microcirculation. In the second part, we discuss the models, which are based on the spatial order reduction to the 1D coordinate. The models of this type require relatively small computational power relative to the 3D models. Within the scope of this approach, it is also possible to include all large vessels of the organism. The 1D models allow simulation of the haemodynamic parameters in every vessel, which is included in the model network. The structure and the parameters of such a network can be set according to the literature data. It also exists methods of medical data segmentation. The 1D models may be derived from the 3D Navier – Stokes equations either by asymptotic analysis or by integrating them over a volume. The major assumptions are symmetric flow and constant shape of the velocity profile over a cross-section. These assumptions are somewhat restrictive and arguable. Some of the current works paying attention to the 1D model’s validation, to the comparing different 1D models and the comparing 1D models with clinical data. The obtained results reveal acceptable accuracy. It allows concluding, that the 1D approach can be used in medical applications. 1D models allow describing several dynamical processes, such as pulse wave propagation, Korotkov’s tones. Some physiological conditions may be included in the 1D models: gravity force, muscles contraction force, regulation and autoregulation.

In various applications arise problems modeled by nonlinear partial differential equations on graphs (networks, trees). In order to study such problems and various extreme situations arose in the problems of designing and optimizing networks developed the computational model based on solving the corresponding boundary problems for partial differential equations of hyperbolic type on graphs (networks, trees). As applications, three different problems were chosen solved in the framework of the general approach of network computational models. The first was modeling of traffic flow. In solving this problem, a macroscopic approach was used in which the transport flow is described by a nonlinear system of second-order hyperbolic equations. The results of numerical simulations showed that the model developed as part of the proposed approach well reproduces the real situation various sections of the Moscow transport network on significant time intervals and can also be used to select the most optimal traffic management strategy in the city. The second was modeling of data flows in computer networks. In this problem data flows of various connections in packet data network were simulated as some continuous medium flows. Conceptual and mathematical network models are proposed. The numerical simulation was carried out in comparison with the NS-2 network simulation system. The results showed that in comparison with the NS-2 packet model the developed streaming model demonstrates significant savings in computing resources while ensuring a good level of similarity and allows us to simulate the behavior of complex globally distributed IP networks. The third was simulation of the distribution of gas impurities in ventilation networks. It was developed the computational mathematical model for the propagation of finely dispersed or gas impurities in ventilation networks using the gas dynamics equations by numerical linking of regions of different sizes. The calculations shown that the model with good accuracy allows to determine the distribution of gas-dynamic parameters in the pipeline network and solve the problems of dynamic ventilation management.

The paper presents the results of numerical simulation of different-temperature water flows turbulent mixing in a T-junctions in the FlowVision software package. The article describes in detail an experimental stand specially designed to obtain boundary conditions that are simple for most computational fluid dynamics software systems. Values of timeaveraged temperatures and velocities in the control sensors and planes were obtained according to the test results. The article presents the system of partial differential equations used in the calculation describing the process of heat and mass transfer in a liquid using the Smagorinsky turbulence model. Boundary conditions are specified that allow setting the random velocity pulsations at the entrance to the computational domain. Distributions of time-averaged water velocity and temperature in control sections and sensors are obtained. The simulation is performed on various computational grids, for which the axes of the global coordinate system coincide with the directions of hot and cold water flows. The possibility for FlowVision PC to construct a computational grid in the simulation process based on changes in flow parameters is shown. The influence of such an algorithm for constructing a computational grid on the results of calculations is estimated. The results of calculations on a diagonal grid using a beveled scheme are given (the direction of the coordinate lines does not coincide with the direction of the tee pipes). The high efficiency of the beveled scheme is shown when modeling flows whose general direction does not coincide with the faces of the calculated cells. A comparison of simulation results on various computational grids is carried out. The numerical results obtained in the FlowVision PC are compared with experimental data and calculations performed using other computing programs. The results of modeling turbulent mixing of water flow of different temperatures in the FlowVision PC are closer to experimental data in comparison with calculations in CFX ANSYS. It is shown that the application of the LES turbulence model on relatively small computational grids in the FlowVision PC allows obtaining results with an error within 5%.

In this paper, we consider the problem of restoring the correspondence matrix based on the observations of real correspondences in Moscow. Following the conventional approach [Gasnikov et al., 2013], the transport network is considered as a directed graph whose edges correspond to road sections and the graph vertices correspond to areas that the traffic participants leave or enter. The number of city residents is considered constant. The problem of restoring the correspondence matrix is to calculate all the correspondence from the $i$ area to the $j$ area.

To restore the matrix, we propose to use one of the most popular methods of calculating the correspondence matrix in urban studies — the entropy model. In our work, which is based on the work [Wilson, 1978], we describe the evolutionary justification of the entropy model and the main idea of the transition to solving the problem of entropy-linear programming (ELP) in calculating the correspondence matrix. To solve the ELP problem, it is proposed to pass to the dual problem. In this paper, we describe several numerical optimization methods for solving this problem: the Sinkhorn method and the Accelerated Sinkhorn method. We provide numerical experiments for the following variants of cost functions: a linear cost function and a superposition of the power and logarithmic cost functions. In these functions, the cost is a combination of average time and distance between areas, which depends on the parameters. The correspondence matrix is calculated for multiple sets of parameters and then we calculate the quality of the restored matrix relative to the known correspondence matrix.

We assume that the noise in the restored correspondence matrix is Gaussian, as a result, we use the standard deviation as a quality metric. The article provides an overview of gradient-free optimization methods for solving non-convex problems. Since the number of parameters of the cost function is small, we use the grid search method to find the optimal parameters of the cost function. Thus, the correspondence matrix calculated for each set of parameters and then the quality of the restored matrix is evaluated relative to the known correspondence matrix. Further, according to the minimum residual value for each cost function, we determine for which cost function and at what parameter values the restored matrix best describes real correspondence.

This work contains a description of the results of modeling the process of maintaining the readiness of a section of the road network under strikes of with specified parameters. A one-dimensional section of road up to 40 km long with a total number of strikes up to 100 during the work of the brigade is considered. A simulation model has been developed for carrying out work to maintain it in working condition by several groups (engineering teams) that are part of the engineering and road division. A multicopter-type unmanned aerial vehicle is used to search for the points of appearance of obstacles. Life cycle schemes of the main participants of the tactical scene have been developed and an event-driven model of the tactical scene has been built. The format of the event log generated as a result of simulation modeling of the process of maintaining a road section is proposed. To visualize the process of maintaining the readiness of a road section, it is proposed to use visualization in the cyclogram format.

An XSL style has been developed for building a cyclogram based on an event log. As an algorithm for making a decision on the assignment of barriers to brigades, the simplest algorithm has been adopted, prescribing choosing the nearest barrier. A criterion describing the effectiveness of maintenance work on the site based on the assessment of the average speed of vehicles on the road section is proposed. Graphs of the dependence of the criterion value and the root-meansquare error depending on the length of the maintained section are plotted and an estimate is obtained for the maximum length of the road section maintained in a state of readiness with specified values for the selected quality indicator with specified characteristics of striking and performance of repair crews. The expediency of carrying out work to maintain readiness by several brigades that are part of the engineering and road division operating autonomously is shown.

The influence of the speed of the unmanned aerial vehicle on the ability to maintain the readiness of the road section is analyzed. The speed range for from 10 to 70 km/h is considered, which corresponds to the technical capabilities of multicoptertype reconnaissance unmanned aerial vehicles. The simulation results can be used as part of a complex simulation model of an army offensive or defensive operation and for solving the problem of optimizing the assignment of tasks to maintain the readiness of road sections to engineering and road brigades. The proposed approach may be of interest for the development of military-oriented strategy games.

The article presents the intermediate results of the development of a control system for a remotely piloted agricultural aircraft (RPAA). The concept of using an automated complex for performing aerochemical work (ACW) designed for processing fields, water areas, forests with the purpose of protection from pests of plants, fertilization is developed. The basic component of the complex is a manned agricultural aircraft MV-500 developed by LLC “Firm “MVEN” (Kazan). The use of the aircraft in unmanned mode will provide an increase in the productivity of the aircraft, will increase the payload.

The article defines the composition of the complex for automation of ACW: aircraft, ground control center, onboard equipment for automated control of the aircraft and the formation of a map of the heights of the section being processed, and the satellite precise positioning system necessary to automate the control of the aircraft. The aircraft is equipped with an automated control system that provides remote control of take-off and landing and automatic control of the flight trajectory at extremely low altitude when performing ACW and performing spatial turns at the boundaries of the treated areas. It is proposed to take off, landing, dropping an aircraft into the ACW exercise area by means of a pilot operator from a ground control station. The ground control point should provide reception and display on the operator's screen of flight information and several types from the aircraft. The operator can control alternately several aircraft during these phases of flight with the help of ground control authorities. In the future, it is planned to automate these stages of flight, leaving behind the pilot-operator control functions and remote control capabilities in special cases. For the navigation of the aircraft, when performing ACW on board, RTK (Real Time Kinematic) equipment is installed, providing a measurement with centimeter accuracy of coordinates and aircraft heights relative to the base station installed in the ground control station. Before the implementation of ACW, a three-dimensional digital map of the processed area is built by adding existing cadastral maps with measurements of the elevations of the section carried out with the help of on-board radio and optical altimeters of the same aircraft.

To date, the following system components have been manufactured and tested: a remotely controlled model of the MV-500 aircraft at a scale of 1:5, a satellite positioning system; system for obtaining images and telemetry information from the board model; autopilot; methods of obtaining three-dimensional digital maps of sections and planning flight trajectories for ACW.

The paper studies the determination for one of the dynamic quality parameter (PDK) of railway vehicles — car body lateral acceleration — by using of computer simulation system for railway vehicles dynamic Simpack Rail. This provide the complex simulation environment with variable velocity depending on the train schedule. The rail vehicle model of typical 1520 mm gauge fright locomotive section used for simulation has been verified by means of the chair “Electric multiple unit cars and locomotives” in the Russian University of Transport (RUT (MIIT)). Due to this homologation the questions of model creating and verification in preprocessor are excluded in this paper. The paper gives the detail description of cartographic track modeling in situation plane, heights plane and superelevation plane based on the real operating data. The statistic parameters (moments) for the rail related track excitation and used cartographic track data of the specified track section in this simulation are given as a numeric and graphical results of reading the prepared data files. The measurement of the car body residual lateral acceleration occur under consideration of the earth gravity acceleration part like the accelerometer measurement in the real world. Finally the desired quality parameter determined by simulation is compared with the same one given by a test drive. The calculation method in both cases is based on the middle value of the absolute maximums picked up within the nonstationary realizations of this parameter. Compared results confirm that this quality factor all the first depends on the velocity and track geometry properties. The simulation of the track in this application uses the strong conformity original track data of the test ride track section. The accepted simplification in the rail vehicle model of fright electric locomotive section (body properties related to the center of gravity, small displacements between the bodies) by keeping the geometric and force law characteristics of the force elements and constraints constant allow in Simpack Rail the simulation with necessary validity of system behavior (reactions).

The article presents the results of a numerical study of the flow structure in a two-dimensional flat diffuser. A feature of diffusers is that they have a complex anisotropic turbulent flow, which occurs due to recirculation flows. The turbulent RANS models, which are based on the Boussinesq hypothesis, are not able to describe the flow in diffusers with sufficient accuracy. Because the Boussinesq hypothesis is based on isotropic turbulence. Therefore, to calculate anisotropic turbulent flows, models are used that do not use this hypothesis. One of such directions in turbulence modeling is the methods of Reynolds stresses. These methods are complex and require rather large computational resources. In this work, a relatively recently developed two-fluid turbulence model was used to study the flow in a flat diffuser. This model is developed on the basis of a two-fluid approach to the problem of turbulence. In contrast to the Reynolds approach, the two-fluid approach allows one to obtain a closed system of turbulence equations using the dynamics of two fluids. Consequently, if empirical equations are used in RANS models for closure, then in the two-fluid model the equations used are exact equations of dynamics. One of the main advantages of the two-fluid model is that it is capable of describing complex anisotropic turbulent flows. In this work, the obtained numerical results for the profiles of the longitudinal velocity, turbulent stresses in various sections of the channel, as well as the friction coefficient are compared with the known experimental data. To demonstrate the advantages of the used turbulence model, the numerical results of the Reynolds stress method EARSM are also presented. For the numerical implementation of the systems of equations of the two-fluid model, a non-stationary system of equations was used, the solution of which asymptotically approached the stationary solution. For this purpose, a finite-difference scheme was used, where the viscosity terms were approximated by the central difference implicitly, and for the convective terms, an explicit scheme against the flow of the second order of accuracy was used. The results are obtained for the Reynolds number Re = 20 000. It is shown that the two-fluid model, despite the use of a uniform computational grid without thickening near the walls, is capable of giving a more accurate solution than the rather complex Reynolds stress method with a high resolution of computational grids.

Under increasing loading and at a constant temperature shape memory solids become deformed in an ideal elastic plastic way as other metals, and the maximum elastic strains are much less than the ultimate plastic ones. The shape is restored at the elevated temperature and low stress level. Phenomenologically, the «reverse» deformation is equivalent to the change in shape under active loading up to sign. Plastic deformation plays a leading role in a non-elastic process; thus, the mechanical behavior should be analyzed within the ideal rigid-plastic model with two loading surfaces. In this model two physical states of the material correspond to the loading surfaces: plastic flow under high stresses and melting at a relatively low temperature. The second section poses a problem of deformation of rigid-plastic bodies at the constant temperature in two forms: as a principle of virtual velocities with the von Mises yield condition and as a requirement of the minimum dissipative functionаl. The equivalence of the accepted definitions and the existence of the generalized solutions is proved for both principles. The third section studies the rigid-plastic model of the solid at the variable temperature with two loading surfaces. For the assumed model two optimal principles are defined that link the external loads and the displacement velocities of the solid points both under active loading and in the process of shape restoration under heating. The existence of generalized velocities is proved for the wide variety of 3D domains. The connection between the variational principles and the variable temperature is ensured by inclusion of the first and second principles of thermodynamics in the calculation model. It is essential that only the phenomenological description of the phenomenon is used in the proving process. The austenite-tomartensite transformations of alloys, which are often the key elements in explanations of the mechanical behavior of shape memory materials, are not used here. The fourth section includes the definition of the shape memory materials as solids with two loading surfaces and proves the existence of solutions within the accepted restrictions. The adequacy of the model and the experiments on deformation of shape memory materials is demonstrated. In the conclusion mathematical problems that could be interesting for future research are defined.