All issues

The article presents the intermediate results of the development of a control system for a remotely piloted agricultural aircraft (RPAA). The concept of using an automated complex for performing aerochemical work (ACW) designed for processing fields, water areas, forests with the purpose of protection from pests of plants, fertilization is developed. The basic component of the complex is a manned agricultural aircraft MV-500 developed by LLC “Firm “MVEN” (Kazan). The use of the aircraft in unmanned mode will provide an increase in the productivity of the aircraft, will increase the payload.

The article defines the composition of the complex for automation of ACW: aircraft, ground control center, onboard equipment for automated control of the aircraft and the formation of a map of the heights of the section being processed, and the satellite precise positioning system necessary to automate the control of the aircraft. The aircraft is equipped with an automated control system that provides remote control of take-off and landing and automatic control of the flight trajectory at extremely low altitude when performing ACW and performing spatial turns at the boundaries of the treated areas. It is proposed to take off, landing, dropping an aircraft into the ACW exercise area by means of a pilot operator from a ground control station. The ground control point should provide reception and display on the operator's screen of flight information and several types from the aircraft. The operator can control alternately several aircraft during these phases of flight with the help of ground control authorities. In the future, it is planned to automate these stages of flight, leaving behind the pilot-operator control functions and remote control capabilities in special cases. For the navigation of the aircraft, when performing ACW on board, RTK (Real Time Kinematic) equipment is installed, providing a measurement with centimeter accuracy of coordinates and aircraft heights relative to the base station installed in the ground control station. Before the implementation of ACW, a three-dimensional digital map of the processed area is built by adding existing cadastral maps with measurements of the elevations of the section carried out with the help of on-board radio and optical altimeters of the same aircraft.

To date, the following system components have been manufactured and tested: a remotely controlled model of the MV-500 aircraft at a scale of 1:5, a satellite positioning system; system for obtaining images and telemetry information from the board model; autopilot; methods of obtaining three-dimensional digital maps of sections and planning flight trajectories for ACW.

The application of a conservative numerical method of fluxes is examined for studying the vortex structures in the massive, fast-turned compact astrophysical objects, which are in self-gravity conditions. The simulation is accomplished for the objects with different mass and rotational speed. The pictures of the vortex structure of objects are visualized. In the calculations the gas-dynamic model is used, in which gas is accepted perfected and nonviscous. Numerical procedure is based on the finite-difference approximation of the conservation laws of the additive characteristics of medium for the finite volume. The “upwind” approximations of the densities of distribution of mass, components of momentum and total energy are applied. For the simulation of the objects, which possess fast-spin motion, the control of conservation for the component of moment of momentun is carried out during calculation. Evolutionary calculation is carried out on the basis of the parallel algorithms, realized on the computer complex of cluster architecture. Algorithms are based on the standardized system of message transfer Message Passing Interface (MPI). The blocking procedures of exchange and non-blocking procedures of exchange with control of the completion of operation are used. The parallelization on the space in two or three directions is carried out depending on the size of integration area and parameters of computational grid. For each subarea the parallelization based on the physical factors is carried out also: the calculations of gas dynamics part and gravitational forces are realized on the different processors, that allows to raise the efficiency of algorithms. The real possibility of the direct calculation of gravitational forces by means of the summation of interaction between all finite volumes in the integration area is shown. For the finite volume methods this approach seems to more consecutive than the solution of Poisson’s equation for the gravitational potential. Numerical calculations were carried out on the computer complex of cluster architecture with the peak productivity 523 TFlops. In the calculations up to thousand processors was used.

The paper studies the determination for one of the dynamic quality parameter (PDK) of railway vehicles — car body lateral acceleration — by using of computer simulation system for railway vehicles dynamic Simpack Rail. This provide the complex simulation environment with variable velocity depending on the train schedule. The rail vehicle model of typical 1520 mm gauge fright locomotive section used for simulation has been verified by means of the chair “Electric multiple unit cars and locomotives” in the Russian University of Transport (RUT (MIIT)). Due to this homologation the questions of model creating and verification in preprocessor are excluded in this paper. The paper gives the detail description of cartographic track modeling in situation plane, heights plane and superelevation plane based on the real operating data. The statistic parameters (moments) for the rail related track excitation and used cartographic track data of the specified track section in this simulation are given as a numeric and graphical results of reading the prepared data files. The measurement of the car body residual lateral acceleration occur under consideration of the earth gravity acceleration part like the accelerometer measurement in the real world. Finally the desired quality parameter determined by simulation is compared with the same one given by a test drive. The calculation method in both cases is based on the middle value of the absolute maximums picked up within the nonstationary realizations of this parameter. Compared results confirm that this quality factor all the first depends on the velocity and track geometry properties. The simulation of the track in this application uses the strong conformity original track data of the test ride track section. The accepted simplification in the rail vehicle model of fright electric locomotive section (body properties related to the center of gravity, small displacements between the bodies) by keeping the geometric and force law characteristics of the force elements and constraints constant allow in Simpack Rail the simulation with necessary validity of system behavior (reactions).

While modeling seismic wave propagation, it is important to take into account nontrivial topography, as this topography causes multiple complex phenomena, such as diffraction at rough surfaces, complex propagation of Rayleigh waves, and side effects caused by wave interference. The primary goal of this research is to construct a method that implements the free surface on topography, utilizing an overset curved grid for characterization, while keeping the main grid structured rectangular. For a combination of the regular and curve-linear grid, the workability of the grid characteristics method using overset grids (also known as the Chimera grid approach) is analyzed. One of the benefits of this approach is computational complexity reduction, caused by the fact that simulation in a regular, homogeneous physical area using a sparse regular rectangle grid is simpler. The simplification of the mesh building mechanism (one grid is regular, and the other can be automatically built using surface data) is a side effect. Despite its simplicity, the method we propose allows us to increase the digitalization of fractured regions and minimize the Courant number. This paper contains various comparisons of modeling results produced by the proposed method-based solver, and results produced by the well-known solver specfem2d, as well as previous modeling results for the same problems. The drawback of the method is that an interpolation error can worsen an overall model accuracy and reduce the computational schema order. Some countermeasures against it are described. For this paper, only two-dimensional models are analyzed. However, the method we propose can be applied to the three-dimensional problems with minimal adaptation required.

The paper provides the mathematical and numerical models of the interrelated thermo- and hydrodynamic processes in the operational mode of development the unified oil-producing complex during the hydrogel flooding of the non-uniform oil reservoir exploited with a system of arbitrarily located injecting wells and producing wells equipped with submersible multistage electrical centrifugal pumps. A special feature of our approach is the modeling of the special ground-based equipment operation (control stations of submersible pumps, drossel devices on the head of producing wells), designed to regulate the operation modes of both the whole complex and its individual elements.

The complete differential model includes equations governing non-stationary two-phase five-component filtration in the reservoir, quasi-stationary heat and mass transfer in the wells and working channels of pumps. Special non-linear boundary conditions and dependencies simulate, respectively, the influence of the drossel diameter on the flow rate and pressure at the wellhead of each producing well and the frequency electric current on the performance characteristics of the submersible pump unit. Oil field development is also regulated by the change in bottom-hole pressure of each injection well, concentration of the gel-forming components pumping into the reservoir, their total volume and duration of injection. The problem is solved numerically using conservative difference schemes constructed on the base of the finite difference method, and developed iterative algorithms oriented on the parallel computing technologies. Numerical model is implemented in a software package which can be considered as the «Intellectual System of Wells» for the virtual control the oil field development.

Flexible woven composites are classified as high-tech innovative materials. Due to the combination of various components of the filler and reinforcement elements, such materials are used in construction, in the defense industry, in shipbuilding and aircraft construction, etc. In the domestic literature, insufficient attention is paid to woven composites that change their geometric structure of the reinforcing layer during deformation. This paper presents an analysis of the previously proposed complex approach to modeling the behavior of flexible woven composites under static uniaxial tension for further generalization of the approach to biaxial tension. The work is aimed at qualitative and quantitative description of mechanical deformation processes occurring in the structure of the studied materials under tension, which include straightening the strands of the reinforcing layer and increasing the value of mutual pressure of the cross-lying reinforcement strands. At the beginning of the deformation process, the straightening of the threads and the increase in mutual pressure of the threads are most intense. With the increase in the level of load, the change of these parameters slows down. For example, the bending of the reinforcement strands goes into the Central tension, and the value of the load from the mutual pressure is no longer increased (tends to constant). To simulate the described processes, the basic geometrical and mechanical parameters of the material affecting the process of forming are introduced, the necessary terminology and description of the characteristics are given. Due to the high geometric nonlinearity of the all processes described in the increments, as in the initial load values there is a significant deformation of the reinforcing layer. For the quantitative and qualitative description of mechanical deformation processes occurring in the reinforcing layer, analytical dependences are derived to determine the increment of the angle of straightening of reinforcement filaments and the load caused by the mutual pressure of the cross-lying filaments at each step of the load increment. For testing of obtained dependencies shows an example of their application for flexible woven composites brands VP4126, VP6131 and VP6545. The simulation results confirmed the assumptions about the processes of straightening the threads and slowing the increase in mutual pressure of the threads. The results and dependences presented in this paper are directly related to the further generalization of the previously proposed analytical models for biaxial tension, since stretching in two directions will significantly reduce the straightening of the threads and increase the amount of mutual pressure under similar loads.

The paper describes an analytical study of hydrodynamic processes taking place in the course of coolant flow through a fuel assembly of the core of a fast neutron sodium-cooled reactor. Within the framework of the study, a procedure and an analytical model were developed based on program complex FlowVision of computational fluid dynamics, which, using proved simplifications, permits to obtain a coefficient of rod lifting margin of a fuel assembly and to study hydrodynamic characteristics of processes taking place in the course of simulation of different initial events influencing motion of a reactor core fuel assembly.

For analytical justification a fuel assembly model was developed, which is equivalent by hydraulic resistance values and permits not to simulate explicitly a complicated full-scale fuel assembly design, thus, decreasing a number of computational cells in the model and, as a result, reducing computational and time resources.

Hydraulic parameters of the equivalent fuel assembly model in program complex FlowVision were analyzed in two stages. At the first stage, to determine the minimum rod lifting margin coefficient of a fuel assembly, steady-state analyses were performed, where various flowrate values were assigned at the model inlet and forces acting upon the assembly were analyzed. A series of dynamic mode analyses was performed at the second stage. Jump-like pressure increase being the initial event which could occur hypothetically in the fast neutron sodium cooled reactor plant was assigned in these modes. Hydrodynamic parameters and forces acting upon the fuel assembly were determined.

The results of the first stage of the analytical study proved the minimum coefficient of rod lifting margin of a fuel assembly of the fast neutron reactor justified in reactor plant design documentation. As a result of the second stage of the study, conclusions were made on impossibility for the fuel assembly to move at the initial event associated with jump-like pressure increase in the reactor pressure chamber.

The work is devoted to the development of a computational algorithm of the Cartesian grid method for studying the interaction of a shock wave with moving bodies with a piecewise linear boundary. The interest in such problems is connected with direct numerical simulation of two-phase media flows. The effect of the particle shape can be important in the problem of dust layer dispersion behind a passing shock wave. Experimental data on the coefficient of aerodynamic drag of non-spherical particles are practically absent.

Mathematical model is based on the two-dimensional Euler equations, which are solved in a region with varying boundaries. The defining system of equations is integrated using an explicit scheme and the Cartesian grid method. The computational algorithm at the time integration step includes: determining the step value, calculating the dynamics of the body movement (determining the force and moment acting on the body; determining the linear and angular velocities of the body; calculating the new coordinates of the body), calculating the gas parameters. At each time step, all cells are divided into two classes – external (inside the body or intersected by its boundaries) and internal (completely filled with gas). The solution of the Euler equations is constructed only in the internal ones. The main difficulty is the calculation of the numerical flux through the edges common to the internal and external cells intersected by the moving boundaries of the bodies. To calculate this flux, we use a two-wave approximation for solving the Riemann problem and the Steger-Warming scheme. A detailed description of the numerical algorithm is presented.

The efficiency of the algorithm is demonstrated on the problem of lifting a cylinder with a base in the form of a circle, ellipse and rectangle behind a passing shock wave. A circular cylinder test was considered in many papers devoted to the immersed boundary methods development. A qualitative and quantitative analysis of the trajectory of the cylinder center mass is carried out on the basis of comparison with the results of simulations presented in eight other works. For a cylinder with a base in the form of an ellipse and a rectangle, a satisfactory agreement was obtained on the dynamics of its movement and rotation in comparison with the available few literary sources. Grid convergence of the results is investigated for the rectangle. It is shown that the relative error of mass conservation law fulfillment decreases with a linear rate.

In this paper, we introduce a new version of Gauss–Newton method for solving a system of nonlinear equations based on ideas of the residual upper bound for a system of nonlinear equations and a quadratic regularization term. The introduced Gauss–Newton method in practice virtually forms the whole parameterized family of the methods solving systems of nonlinear equations and regression problems. The developed family of Gauss–Newton methods completely consists of iterative methods with generalization for cases of non-euclidean normed spaces, including special forms of Levenberg–Marquardt algorithms. The developed methods use the local model based on a parameterized proximal mapping allowing us to use an inexact oracle of «black–box» form with restrictions for the computational precision and computational complexity. We perform an efficiency analysis including global and local convergence for the developed family of methods with an arbitrary oracle in terms of iteration complexity, precision and complexity of both local model and oracle, problem dimensionality. We present global sublinear convergence rates for methods of the proposed family for solving a system of nonlinear equations, consisting of Lipschitz smooth functions. We prove local superlinear convergence under extra natural non-degeneracy assumptions for system of nonlinear functions. We prove both local and global linear convergence for a system of nonlinear equations under Polyak–Lojasiewicz condition for proposed Gauss– Newton methods. Besides theoretical justifications of methods we also consider practical implementation issues. In particular, for conducted experiments we present effective computational schemes for the exact oracle regarding to the dimensionality of a problem. The proposed family of methods unites several existing and frequent in practice Gauss–Newton method modifications, allowing us to construct a flexible and convenient method implementable using standard convex optimization and computational linear algebra techniques.

Modern methods of complex planning the execution of task packages in multistage systems are characterized by the presence of restrictions on the dimension of the problem being solved, the impossibility of guaranteed obtaining effective solutions for various values of its input parameters, as well as the impossibility of registration the conditions for the formation of sets from the result and the restriction on the interval duration of time of the system operating. The decomposition of the generalized function of the system into a set of hierarchically interconnected subfunctions is implemented to solve the problem of scheduling the execution of task packages with generating sets of results and the restriction on the interval duration of time for the functioning of the system. The use of decomposition made it possible to employ the hierarchical approach for planning the execution of task packages in multistage systems, which provides the determination of decisions by the composition of task groups at the first level of the hierarchy decisions by the composition of task packages groups executed during time intervals of limited duration at the second level and schedules for executing packages at the third level the hierarchy. In order to evaluate decisions on the composition of packages, the results of their execution, obtained during the specified time intervals, are distributed among the packages. The apparatus of the theory of hierarchical games is used to determine complex solutions. A model of a hierarchical game for making decisions by the compositions of packages, groups of packages and schedules of executing packages is built, which is a system of hierarchically interconnected criteria for optimizing decisions. The model registers the condition for the formation of sets from the results of the execution of task packages and restriction on duration of time intervals of its operating. The problem of determining the compositions of task packages and groups of task packages is NP-hard; therefore, its solution requires the use of approximate optimization methods. In order to optimize groups of task packages, the construction of a method for formulating initial solutions by their compositions has been implemented, which are further optimized. Moreover, a algorithm for distributing the results of executing task packages obtained during time intervals of limited duration by sets is formulated. The method of local solutions optimization by composition of packages groups, in accordance with which packages are excluded from groups, the results of which are not included in sets, and packages, that aren’t included in any group, is proposed. The software implementation of the considered method of complex optimization of the compositions of task packages, groups of task packages, and schedules for executing task packages from groups (including the implementation of the method for optimizing the compositions of groups of task packages) has been performed. With its use, studies of the features of the considered planning task are carried out. Conclusion are formulated concerning the dependence of the efficiency of scheduling the execution of task packages in multistage system under the introduced conditions from the input parameters of the problem. The use of the method of local optimization of the compositions of groups of task packages allows to increase the number of formed sets from the results of task execution in packages from groups by 60% in comparison with fixed groups (which do not imply optimization).