All issues

We consider a mechanical system consisting of a rigid body and two masses that move inside the body along mutually perpendicular guides. The body has a flat face, which rests on a horizontal rough plane. The masses move inside the body in a vertical plane according to a harmonic law with the same period. It is assumed that the friction forces arising in the area of contact between the body and the supporting plane are described by the classical model of dry Coulomb friction, and the parameters of the problem are chosen so that the body can perform translationally rectilinearly motion. This mechanical system can serve as the simplest model of a capsule robot moving on a solid surface by moving internal elements.

We study the modes of motion of a body in which its velocity is periodic with a period equal to the period of motion of the internal masses. It is shown that if the body can starts to move from a state of rest by means of displacements of the masses, then for any permissible values of the problem parameters there is a periodic mode of motion. Depending on the parameter values, the nature of the periodic motion can be essentially different. In particular, both reversible and nonreversible driving modes are possible. In the non-reversion mode, the body moves in the same direction, and intervals of movement alternate with intervals of rest (body sticking). In the reversal mode, the body moves in both positive and negative directions over a time interval equal to one period. In this case, the body makes two stops during the period of movement. After stopping, the body either immediately continues moving in the opposite direction, or enters a sticking zone and rests for a finite period of time, and then stats moving in the opposite direction. It was also found that, at certain parameter values, a periodic reversal mode is possible, in which the body moves without sticking. A detailed classification of all possible types of periodic motion modes was carried out. Their complete qualitative description is given and the regions of their existence in the three-dimensional space of the parameters are constructed.

While modeling seismic wave propagation, it is important to take into account nontrivial topography, as this topography causes multiple complex phenomena, such as diffraction at rough surfaces, complex propagation of Rayleigh waves, and side effects caused by wave interference. The primary goal of this research is to construct a method that implements the free surface on topography, utilizing an overset curved grid for characterization, while keeping the main grid structured rectangular. For a combination of the regular and curve-linear grid, the workability of the grid characteristics method using overset grids (also known as the Chimera grid approach) is analyzed. One of the benefits of this approach is computational complexity reduction, caused by the fact that simulation in a regular, homogeneous physical area using a sparse regular rectangle grid is simpler. The simplification of the mesh building mechanism (one grid is regular, and the other can be automatically built using surface data) is a side effect. Despite its simplicity, the method we propose allows us to increase the digitalization of fractured regions and minimize the Courant number. This paper contains various comparisons of modeling results produced by the proposed method-based solver, and results produced by the well-known solver specfem2d, as well as previous modeling results for the same problems. The drawback of the method is that an interpolation error can worsen an overall model accuracy and reduce the computational schema order. Some countermeasures against it are described. For this paper, only two-dimensional models are analyzed. However, the method we propose can be applied to the three-dimensional problems with minimal adaptation required.

In this paper a fluid flow between two close located rough surfaces depending on their location and discontinuity in contact areas is investigated. The area between surfaces is considered as the porous layer with the variable permeability, depending on roughness and closure of surfaces. For obtaining closure-permeability function, the flow on the small region of surfaces (100 $\mu$m) is modeled, for which the surfaces roughness profile created by fractal function of Weierstrass – Mandelbrot. The 3D-domain for this calculation fill out the area between valleys and peaks of two surfaces, located at some distance from each other. If the surfaces get closer, a contacts between roughness peaks will appears and it leads to the local discontinuities in the domain. For the assumed surfaces closure and boundary conditions the mass flow and pressure drop is calculated and based on that, permeability of the equivalent porous layer is evaluated.The calculation results of permeability obtained for set of surfaces closure were approximated by a polynom. This allows us to calculate the actual flow parameters in a thin layer of variable thickness, the length of which is much larger than the scale of the surface roughness. As an example, showing the application of this technique, flow in the gap between the billet and conical die in 3D-formulation is modeled. In this problem the permeability of an equivalent porous layer calculated for the condition of a linear decreased gap.

This paper presents a methodology for modeling centrifugal pumps using the example of the NM 1250 260 main oil centrifugal pump. We use FlowVision CFD software as the numerical modeling instrument. Bench tests and numerical modeling use water as a working fluid. The geometrical model of the pump is fully three-dimensional and includes the pump housing to account for leakages. In order to reduce the required computational resources, the methodology specifies leakages using flow rate rather than directly modeling them. Surface roughness influences flow through the wall function model. The wall function model uses an equivalent sand roughness, and a formula for converting real roughness into equivalent sand roughness is applied in this work. FlowVision uses the sliding mesh method for simulation of the rotation of the impeller. This approach takes into account the nonstationary interaction between the rotor and diffuser of the pump, allowing for accurate resolution of recirculation vortices that occur at low flow rates.

The developed methodology has achieved high consistency between numerical simulations results and experiments at all pump operating conditions. The deviation in efficiency at nominal conditions is 0.42%, and in head is 1.9%. The deviation of calculated characteristics from experimental ones increases as the flow rate increases and reaches a maximum at the far-right point of the characteristic curve (up to 4.8% in head). This phenomenon occurs due to a slight mismatch between the geometric model of the impeller used in the calculation and the real pump model from the experiment. However, the average arithmetic relative deviation between numerical modeling and experiment for pump efficiency at 6 points is 0.39%, with an experimental efficiency measurement error of 0.72%. This meets the accuracy requirements for calculations. In the future, this methodology can be used for a series of optimization and strength calculations, as modeling does not require significant computational resources and takes into account the non-stationary nature of flow in the pump.

Corrosion damage to metals and alloys is one of the main problems of strength and durability of metal structures and products operated in contact with chemically aggressive environments. Recently, there has been a growing interest in computer modeling of the evolution of corrosion damage, especially pitting corrosion, for a deeper understanding of the corrosion process, its impact on the morphology, physical and chemical properties of the surface and mechanical strength of the material. This is mainly due to the complexity of analytical and high cost of experimental in situ studies of real corrosion processes. However, the computing power of modern computers allows you to calculate corrosion with high accuracy only on relatively small areas of the surface. Therefore, the development of new mathematical models that allow calculating large areas for predicting the evolution of corrosion damage to metals is currently an urgent problem.

In this paper, the evolution of the corrosion front in the interaction of a polycrystalline metal surface with a liquid aggressive medium was studied using a computer model based on a cellular automat. A distinctive feature of the model is the specification of the solid body structure in the form of Voronoi polygons used for modeling polycrystalline alloys. Corrosion destruction was performed by setting the probability function of the transition between cells of the cellular automaton. It was taken into account that the corrosion strength of the grains varies due to crystallographic anisotropy. It is shown that this leads to the formation of a rough phase boundary during the corrosion process. Reducing the concentration of active particles in a solution of an aggressive medium during a chemical reaction leads to corrosion attenuation in a finite number of calculation iterations. It is established that the final morphology of the phase boundary has a fractal structure with a dimension of 1.323 ± 0.002 close to the dimension of the gradient percolation front, which is in good agreement with the fractal dimension of the etching front of a polycrystalline aluminum-magnesium alloy AlMg6 with a concentrated solution of hydrochloric acid. It is shown that corrosion of a polycrystalline metal in a liquid aggressive medium is a new example of a topochemical process, the kinetics of which is described by the Kolmogorov–Johnson– Meil–Avrami theory.

Social media is a crucial indicator of the position of assets in the financial market. The paper describes the rigid solution for the classification problem to determine the influence of social media activity on financial market movements. Reputable crypto traders influencers are selected. Twitter posts packages are used as data. The methods of text, which are characterized by the numerous use of slang words and abbreviations, and preprocessing consist in lemmatization of Stanza and the use of regular expressions. A word is considered as an element of a vector of a data unit in the course of solving the problem of binary classification. The best markup parameters for processing Binance candles are searched for. Methods of feature selection, which is necessary for a precise description of text data and the subsequent process of establishing dependence, are represented by machine learning and statistical analysis. First, the feature selection is used based on the information criterion. This approach is implemented in a random forest model and is relevant for the task of feature selection for splitting nodes in a decision tree. The second one is based on the rigid compilation of a binary vector during a rough check of the presence or absence of a word in the package and counting the sum of the elements of this vector. Then a decision is made depending on the superiority of this sum over the threshold value that is predetermined previously by analyzing the frequency distribution of mentions of the word. The algorithm used to solve the problem was named benchmark and analyzed as a tool. Similar algorithms are often used in automated trading strategies. In the course of the study, observations of the influence of frequently occurring words, which are used as a basis of dimension 2 and 3 in vectorization, are described as well.

The paper considers the basic model of competitive interactions and its use for the analysis and description of social processes. The peculiarity of the model is that it describes the interaction of several competing actors, while actors can vary the strategy of their actions, in particular, form coalitions to jointly counter a common enemy. As a result of modeling, various modes of competitive interaction were identified, their classification was conducted, and their features were described. In the course of the study, the attention is paid to the so-called “rough” (according to A.A. Andronov) cases of the implementation of competitive interaction, which until now have rarely been considered in the scientific literature, but are quite common in real life. Using a basic mathematical model, the conditions for the implementation of various modes of competitive interactions are considered, the conditions for the transition from one mode to another are determined, examples of the implementation of these modes in the economy, social and political life are given. It is shown that with a relatively low level of competition, which is non-antagonistic in nature, competition can lead to an increase in the activity of interacting actors and to overall economic growth. Moreover, in the presence of expanding resource opportunities (as long as such opportunities remain), this growth may have a hyperbolic character. With a decrease in resource capabilities and increased competition, there is a transition to an oscillatory mode, when weaker actors unite to jointly counteract stronger ones. With a further decrease in resource opportunities and increased competition, there is a transition to the formation of stable hierarchical structures. At the same time, the model shows that at a certain moment there is a loss of stability, the system becomes “rough” according to A.A. Andronov and sensitive to fluctuations in parameter changes. As a result, the existing hierarchies may collapse and be replaced by new ones. With a further increase in the intensity of competition, the actor-leader completely suppresses his opponents and establishes monopolism. Examples from economic, social, and political life are given, illustrating the patterns identified on the basis of modeling using the basic model of competition. The obtained results can be used in the analysis, modeling and forecasting of socioeconomic and political processes.