All issues

This paper presents a methodology for modeling centrifugal pumps using the example of the NM 1250 260 main oil centrifugal pump. We use FlowVision CFD software as the numerical modeling instrument. Bench tests and numerical modeling use water as a working fluid. The geometrical model of the pump is fully three-dimensional and includes the pump housing to account for leakages. In order to reduce the required computational resources, the methodology specifies leakages using flow rate rather than directly modeling them. Surface roughness influences flow through the wall function model. The wall function model uses an equivalent sand roughness, and a formula for converting real roughness into equivalent sand roughness is applied in this work. FlowVision uses the sliding mesh method for simulation of the rotation of the impeller. This approach takes into account the nonstationary interaction between the rotor and diffuser of the pump, allowing for accurate resolution of recirculation vortices that occur at low flow rates.

The developed methodology has achieved high consistency between numerical simulations results and experiments at all pump operating conditions. The deviation in efficiency at nominal conditions is 0.42%, and in head is 1.9%. The deviation of calculated characteristics from experimental ones increases as the flow rate increases and reaches a maximum at the far-right point of the characteristic curve (up to 4.8% in head). This phenomenon occurs due to a slight mismatch between the geometric model of the impeller used in the calculation and the real pump model from the experiment. However, the average arithmetic relative deviation between numerical modeling and experiment for pump efficiency at 6 points is 0.39%, with an experimental efficiency measurement error of 0.72%. This meets the accuracy requirements for calculations. In the future, this methodology can be used for a series of optimization and strength calculations, as modeling does not require significant computational resources and takes into account the non-stationary nature of flow in the pump.

As the population of cities grows, the need to plan for the development of transport infrastructure becomes more acute. For this purpose, transport modeling packages are created. These packages usually contain a set of convex optimization problems, the iterative solution of which leads to the desired equilibrium distribution of flows along the paths. One of the directions for the development of transport modeling is the construction of more accurate generalized models that take into account different types of passengers, their travel purposes, as well as the specifics of personal and public modes of transport that agents can use. Another important direction of transport models development is to improve the efficiency of the calculations performed. Since, due to the large dimension of modern transport networks, the search for a numerical solution to the problem of equilibrium distribution of flows along the paths is quite expensive. The iterative nature of the entire solution process only makes this worse. One of the approaches leading to a reduction in the number of calculations performed is the construction of consistent models that allow to combine the blocks of a 4-stage model into a single optimization problem. This makes it possible to eliminate the iterative running of blocks, moving from solving a separate optimization problem at each stage to some general problem. Early work has proven that such approaches provide equivalent solutions. However, it is worth considering the validity and interpretability of these methods. The purpose of this article is to substantiate a single problem, that combines both the calculation of the trip matrix and the modal choice, for the generalized case when there are different layers of demand, types of agents and classes of vehicles in the transport network. The article provides possible interpretations for the gauge parameters used in the problem, as well as for the dual factors associated with the balance constraints. The authors of the article also show the possibility of combining the considered problem with a block for determining network load into a single optimization problem.

Considered the application of physics-informed neural networks using multi layer perceptrons to solve Cauchy initial value problems in which the right-hand sides of the equation are continuous monotonically increasing, decreasing or oscillating functions. With the use of the computational experiments the influence of the construction of the approximate neural network solution, neural network structure, optimization algorithm and software implementation means on the learning process and the accuracy of the obtained solution is studied. The analysis of the efficiency of the most frequently used machine learning frameworks in software development with the programming languages Python and C# is carried out. It is shown that the use of C# language allows to reduce the time of neural networks training by 20–40%. The choice of different activation functions affects the learning process and the accuracy of the approximate solution. The most effective functions in the considered problems are sigmoid and hyperbolic tangent. The minimum of the loss function is achieved at the certain number of neurons of the hidden layer of a single-layer neural network for a fixed training time of the neural network model. It’s also mentioned that the complication of the network structure increasing the number of neurons does not improve the training results. At the same time, the size of the grid step between the points of the training sample, providing a minimum of the loss function, is almost the same for the considered Cauchy problems. Training single-layer neural networks, the Adam method and its modifications are the most effective to solve the optimization problems. Additionally, the application of twoand three-layer neural networks is considered. It is shown that in these cases it is reasonable to use the LBFGS algorithm, which, in comparison with the Adam method, in some cases requires much shorter training time achieving the same solution accuracy. The specificity of neural network training for Cauchy problems in which the solution is an oscillating function with monotonically decreasing amplitude is also investigated. For these problems, it is necessary to construct a neural network solution with variable weight coefficient rather than with constant one, which improves the solution in the grid cells located near by the end point of the solution interval.

This paper examines the impact of the spatial resolution of a discretized (lattice) representation of the environment on the efficiency and correctness of optimal pathfinding in complex environments. Scenarios are considered that may include bottlenecks, non-uniform obstacle distributions, and areas of increased safety requirements in the immediate vicinity of obstacles. Despite the widespread use of lattice representations of the environment in robotics due to their compatibility with sensor data and support for classical trajectory planning algorithms, the resolution of these lattices has a significant impact on both goal reachability and optimal path performance. An algorithm is proposed that combines environmental connectivity analysis, trajectory optimization, and geometric safety refinement. In the first stage, the Leath algorithm is used to estimate the reachability of the target point by identifying a connected component containing the starting position. Upon confirmation of the target point’s reachability, the A* algorithm is applied to the nodes of this component in the second stage to construct a path that simultaneously minimizes both the path length and the risk of collision. In the third stage, a refined obstacle distance estimate is performed for nodes located in safety zones using a combination of the Gilbert – Johnson –Keerthi (GJK) and expanding polyhedron (EPA) algorithms. Experimental analysis revealed a nonlinear relationship between the probability of the existence and effectiveness of an optimal path and the lattice parameters. Specifically, reducing the spatial resolution of the lattice increases the likelihood of connectivity loss and target unreachability, while increasing its spatial resolution increases computational complexity without a proportional improvement in the optimal path’s performance.

The approach to optimization of integral estimation of bio-systems state is presented. The approach is included the procedures of decreasing of variability of integral estimation based on statistical modeling of experimental data set and optimization the quantity of a state characteristics on a base of their relative contribution to the integral estimation using parallel calculation.

The paper presents an optimization approach to microstructure simulation. Porosity function was optimized by numerical method, grain-size model was optimized by complex method based on criteria of model quality. Methods have been validated on examples. Presented new regression model of model quality. Actual application of proposed method is 3D reconstruction of core sample microstructure. Presented results suggest to prolongation of investigations. 

The practical application of nuclear medicine demonstrates the continued information deficiency of the algorithms and programs that provide visualization and analysis of medical images. The aim of the study was to determine the principles of optimizing the processing of planar osteostsintigraphy on the basis of сomputer aided diagnosis (CAD) for analysis of texture descriptions of images of metastatic zones on planar scintigrams of skeleton. A computer-aided diagnosis system for analysis of skeletal metastases based on planar scintigraphy data has been developed. This system includes skeleton image segmentation, calculation of textural, histogram and morphometrical parameters and the creation of a training set. For study of metastatic images’ textural characteristics on planar scintigrams of skeleton was developed the computer program of automatic analysis of skeletal metastases is used from data of planar scintigraphy. Also expert evaluation was used to distinguishing ‘pathological’ (metastatic) from ‘physiological’ (non-metastatic) radiopharmaceutical hyperfixation zones in which Haralick’s textural features were determined: autocorrelation, contrast, ‘forth moment’ and heterogeneity. This program was established on the principles of сomputer aided diagnosis researches planar scintigrams of skeletal patients with metastatic breast cancer hearths hyperfixation of radiopharmaceuticals were identified. Calculated parameters were made such as brightness, smoothness, the third moment of brightness, brightness uniformity, entropy brightness. It has been established that in most areas of the skeleton of histogram values of parameters in pathologic hyperfixation of radiopharmaceuticals predominate over the same values in the physiological. Most often pathological hyperfixation of radiopharmaceuticals as the front and rear fixed scintigramms prevalence of brightness and smoothness of the image brightness in comparison with those of the physiological hyperfixation of radiopharmaceuticals. Separate figures histogram analysis can be used in specifying the diagnosis of metastases in the mathematical modeling and interpretation bone scintigraphy. Separate figures histogram analysis can be used in specifying the diagnosis of metastases in the mathematical modeling and interpretation bone scintigraphy.

The paper proposes a mathematical model for the therapy of glioma, taking into account the blood-brain barrier, radiotherapy and antibody therapy. The parameters were estimated from experimental data and the evaluation of the effect of parameter values on the effectiveness of treatment and the prognosis of the disease were obtained. The possible variants of sequential use of radiotherapy and the effect of antibodies have been explored. The combined use of radiotherapy with intravenous administration of $mab$ $Cx43$ leads to a potentiation of the therapeutic effect in glioma.

Radiotherapy must precede chemotherapy, as radio exposure reduces the barrier function of endothelial cells. Endothelial cells of the brain vessels fit tightly to each other. Between their walls are formed so-called tight contacts, whose role in the provision of BBB is that they prevent the penetration into the brain tissue of various undesirable substances from the bloodstream. Dense contacts between endothelial cells block the intercellular passive transport.

The mathematical model consists of a continuous part and a discrete one. Experimental data on the volume of glioma show the following interesting dynamics: after cessation of radio exposure, tumor growth does not resume immediately, but there is some time interval during which glioma does not grow. Glioma cells are divided into two groups. The first group is living cells that divide as fast as possible. The second group is cells affected by radiation. As a measure of the health of the blood-brain barrier system, the ratios of the number of BBB cells at the current moment to the number of cells at rest, that is, on average healthy state, are chosen.

The continuous part of the model includes a description of the division of both types of glioma cells, the recovery of BBB cells, and the dynamics of the drug. Reducing the number of well-functioning BBB cells facilitates the penetration of the drug to brain cells, that is, enhances the action of the drug. At the same time, the rate of division of glioma cells does not increase, since it is limited not by the deficiency of nutrients available to cells, but by the internal mechanisms of the cell. The discrete part of the mathematical model includes the operator of radio interaction, which is applied to the indicator of BBB and to glial cells.

Within the framework of the mathematical model of treatment of a cancer tumor (glioma), the problem of optimal control with phase constraints is solved. The patient’s condition is described by two variables: the volume of the tumor and the condition of the BBB. The phase constraints delineate a certain area in the space of these indicators, which we call the survival area. Our task is to find such treatment strategies that minimize the time of treatment, maximize the patient’s rest time, and at the same time allow state indicators not to exceed the permitted limits. Since the task of survival is to maximize the patient’s lifespan, it is precisely such treatment strategies that return the indicators to their original position (and we see periodic trajectories on the graphs). Periodic trajectories indicate that the deadly disease is translated into a chronic one.

The method of balanced identification was used to describe the response of Net Ecosystem Exchange of CO₂ (NEE) to change of environmental factors, and to fill the gaps in continuous CO₂ flux measurements in a sphagnum peat bog in the Tver region. The measurements were provided in the peat bog by the eddy covariance method from August to November of 2017. Due to rainy weather conditions and recurrent periods with low atmospheric turbulence the gap proportion in measured CO₂ fluxes at our experimental site during the entire period of measurements exceeded 40%. The model developed for the gap filling in long-term experimental data considers the NEE as a difference between Ecosystem Respiration (RE) and Gross Primary Production (GPP), i.e. key processes of ecosystem functioning, and their dependence on incoming solar radiation (Q), soil temperature (T), water vapor pressure deficit (VPD) and ground water level (WL). Applied for this purpose the balanced identification method is based on the search for the optimal ratio between the model simplicity and the data fitting accuracy — the ratio providing the minimum of the modeling error estimated by the cross validation method. The obtained numerical solutions are characterized by minimum necessary nonlinearity (curvature) that provides sufficient interpolation and extrapolation characteristics of the developed models. It is particularly important to fill the missing values in NEE measurements. Reviewing the temporary variability of NEE and key environmental factors allowed to reveal a statistically significant dependence of GPP on Q, T, and VPD, and RE — on T and WL, respectively. At the same time, the inaccuracy of applied method for simulation of the mean daily NEE, was less than 10%, and the error in NEE estimates by the method was higher than by the REddyProc model considering the influence on NEE of fewer number of environmental parameters. Analyzing the gap-filled time series of NEE allowed to derive the diurnal and inter-daily variability of NEE and to obtain cumulative CO₂ fluxs in the peat bog for selected summer-autumn period. It was shown, that the rate of CO₂ fixation by peat bog vegetation in August was significantly higher than the rate of ecosystem respiration, while since September due to strong decrease of GPP the peat bog was turned into a consistent source of CO₂ for the atmosphere.

The reconstruction of charged particle trajectories in tracking detectors is a key problem in the analysis of experimental data for high energy and nuclear physics.

The amount of data in modern experiments is so large that classical tracking methods such as Kalman filter can not process them fast enough. To solve this problem, we have developed two neural network algorithms of track recognition, based on deep learning architectures, for local (track by track) and global (all tracks in an event) tracking in the GEM tracker of the BM@N experiment at JINR (Dubna). The advantage of deep neural networks is the ability to detect hidden nonlinear dependencies in data and the capability of parallel execution of underlying linear algebra operations.

In this work we generalize these algorithms to the cylindrical GEM inner tracker of BESIII experiment. The neural network model RDGraphNet for global track finding, based on the reverse directed graph, has been successfully adapted. After training on Monte Carlo data, testing showed encouraging results: recall of 98% and precision of 86% for track finding.

The local neural network model TrackNETv2 was also adapted to BESIII CGEM successfully. Since the tracker has only three detecting layers, an additional neuro-classifier to filter out false tracks have been introduced. Preliminary tests demonstrated the recall value at the first stage of 99%. After applying the neuro-classifier, the precision was 77% with a slight decrease of the recall to 94%. This result can be improved after the further model optimization.