All issues

A 2D numerical model of the immersion of a cold oceanic plate into the thickness of the Earth’s upper mantle has been developed, where the stage of the initial immersion of the plate is preceded by the establishment of a regime of thermogravitational convection of the mantle substance. The model approximation of the mantle is a two-dimensional image of an incompressible Newtonian quasi-liquid in a Cartesian coordinate system, where, due to the high viscosity of the medium, the equations of mantle convection are accepted in the Stokes approximation. It is assumed that seawater that has leaked here enters the first horizons of the mantle together with the plate. With depth, the increase in pressure and temperature leads to certain losses of its light fractions and fluids, losses of water and gases of water-containing minerals of the plate, restructuring of their crystal lattice and, as a consequence, phase transformations. These losses cause an increase in the plate density and an uneven distribution of stresses along the plate (the initial sections of the plate are denser), which subsequently, together with the effect of mantle currents on the plate, causes its fragmentation. The state of mantle convection is considered when the plate and its individual fragments have descended to the bottom of the upper mantle. Computational schemes for solving the model equations have been developed. Mantle convection calculations are performed in terms of the Stokes approximation for vorticity and the stream function, and SPH is used to calculate the state and subsidence of the plate. A number of computational experiments have been performed. It is shown that fragmentation of the plate occurs due to the effect of mantle convection on the plate and the development of inhomogeneous stress fields along the plate. Following the equations of the model, the time of the final stage of subduction is estimated, i.e. the time of the entire oceanic plate reaching the bottom of the upper mantle. In geodynamics, this process is determined by the collision of plates that immediately follows subduction and is usually considered as the final stage of the Wilson cycle (i. e., the cycle of development of folded belts).

The paper provides the mathematical and numerical models of the interrelated thermo- and hydrodynamic processes in the operational mode of development the unified oil-producing complex during the hydrogel flooding of the non-uniform oil reservoir exploited with a system of arbitrarily located injecting wells and producing wells equipped with submersible multistage electrical centrifugal pumps. A special feature of our approach is the modeling of the special ground-based equipment operation (control stations of submersible pumps, drossel devices on the head of producing wells), designed to regulate the operation modes of both the whole complex and its individual elements.

The complete differential model includes equations governing non-stationary two-phase five-component filtration in the reservoir, quasi-stationary heat and mass transfer in the wells and working channels of pumps. Special non-linear boundary conditions and dependencies simulate, respectively, the influence of the drossel diameter on the flow rate and pressure at the wellhead of each producing well and the frequency electric current on the performance characteristics of the submersible pump unit. Oil field development is also regulated by the change in bottom-hole pressure of each injection well, concentration of the gel-forming components pumping into the reservoir, their total volume and duration of injection. The problem is solved numerically using conservative difference schemes constructed on the base of the finite difference method, and developed iterative algorithms oriented on the parallel computing technologies. Numerical model is implemented in a software package which can be considered as the «Intellectual System of Wells» for the virtual control the oil field development.

A new flow modeling method on unstructured grid was proposed. As a basis system this method used quasi-hydro-dynamic equations. The finite volume method vas used for solving these equations. The Delaunay triangulation was used for constructing mesh. This proposed method was tested in modeling of incompressible flow through a channel with complex profile. The acquired results showed that the proposed method could be used in flow modeling in unstructured grid.

The mathematical model, finite-difference schemes and algorithms for computation of transient thermoand hydrodynamic processes involved in commissioning the unified system including the oil producing well, electrical submersible pump and fractured-porous reservoir with bottom water are developed. These models are implemented in the computer package to simulate transient processes with simultaneous visualization of their results along with computations. An important feature of the package Oil-RWP is its interaction with the special external program GCS which simulates the work of the surface electric control station and data exchange between these two programs. The package Oil-RWP sends telemetry data and current parameters of the operating submersible unit to the program module GCS (direct coupling). The station controller analyzes incoming data and generates the required control parameters for the submersible pump. These parameters are sent to Oil-RWP (feedback). Such an approach allows us to consider the developed software as the “Intellectual Well System”.

Some principal results of the simulations can be briefly presented as follows. The transient time between inaction and quasi-steady operation of the producing well depends on the well stream watering, filtration and capacitive parameters of oil reservoir, physical-chemical properties of phases and technical characteristics of the submersible unit. For the large time solution of the nonstationary equations governing the nonsteady processes is practically identical to the inverse quasi-stationary problem solution with the same initial data. The developed software package is an effective tool for analysis, forecast and optimization of the exploiting parameters of the unified oil-producing complex during its commissioning into the operating regime.