All issues

The need to model high-speed flows of compressible media with shock waves in the presence of dense curtains or layers of particles arises when studying various processes, such as the dispersion of particles from a layer behind a shock wave or propagation of combustion waves in heterogeneous explosives. These directions have been successfully developed over the past few decades, but the corresponding mathematical models and computational algorithms continue to be actively improved. The mechanisms of wave processes in two-phase media differ in different models, so it is important to continue researching and improving these models.

The paper is devoted to the numerical study of the propagation of disturbances inside a sand bed under the action of successive impacts of a normally incident air shock wave. The setting of the problem follows the experiments of A. T.Akhmetov with co-authors. The aim of this study is to investigate the possible reasons for signal amplification on the pressure sensor within the bed, as observed under some conditions in experiments. The mathematical model is based on a one-dimensional system of Baer –Nunziato equations for describing dense flows of two-phase media taking into account intergranular stresses in the particle phase. The computational algorithm is based on the Godunov method for the Baer – Nunziato equations.

The paper describes the dynamics of waves inside and outside a particle bed after applying first and second pressure pulses to it. The main components of the flow within the bed are filtration waves in the gas phase and compaction waves in the solid phase. The compaction wave, generated by the first pulse and reflected from the walls of the shock tube, interacts with the filtration wave caused by the second pulse. As a result, the signal measured by the pressure sensor inside the bed has a sharp peak, explaining the new effect observed in experiments.

The work deals the implementation of a three-dimensional mathematical model of the nonlinear time-varying temperature control and a numerical method of solving it.

The paper provides a review of the existing methods of signals’ processing within the conditions of the Rice statistical model applicability. There are considered the principle development directions, the existing limitations and the improvement possibilities concerning the methods of solving the tasks of noise suppression and analyzed signals’ filtration by the example of magnetic-resonance visualization. A conception of a new approach to joint calculation of Rician signal’s both parameters has been developed based on the method of moments in two variants of its implementation. The computer simulation and the comparative analysis of the obtained numerical results have been conducted.

The technique of simplification of mathematical model of a chemical reaction by reducing the number of steps of the reaction scheme, based on an analysis of sensitivity to changes in the objective function of the model parameters, is proposed. The reduced scheme of model reaction of formaldehyde oxidation is received. Functional characterizes the measure of proximity to the calculated values for the initial kinetic reaction scheme and the scheme resulting disturbance of its parameters. The advantage of this technique is the ability to analyze complex kinetic schemes and reduction of kinetic models to a size suitable for practical use. The results of computational experiments under different reaction conditions can be included in the functional and thus to receive the reduce scheme, which is consistent the detailed scheme for the desired range of conditions. Sensitivity analysis of the functional model allows to identify those parameters, which provide the largest (or smallest) the contribution to the result of the process simulation. The mathematical model can contain parameters, which change of values do not affect the qualitative and quantitative description of the process. The contribution of these parameters in the functional value won’t be of great importance. Thus it can be eliminated from consideration, which do not serve for modeling kinetic curves substances. The kinetic scheme of formaldehyde oxidation, the detailed mechanism which includes 25 stages and 15 substances, were investigated using this method. On the basis of the local and global sensitivity analysis, the most important stage of the process that affect the overall dynamics of the target concentrations of the reaction. The reduced scheme of model reaction of formaldehyde oxidation is received. This scheme also describes the behavior of the main substances, as detailed scheme, but has a much smaller number of reaction stages. The results of the comparative analysis of modeling of formaldehyde oxidation on detailed and reduced schemes are given. Computational aspects of the problems of chemical kinetics by Sobol’ global method an example of this reaction are specified. The comparison results are local, global and total sensitivity indices are given.

This article represents numerical simulation technique for determining effective spectral electromagnetic properties (effective electrical conductivity and relative dielectric permittivity) of saturated porous media. Information about these properties is vastly applied during the interpretation of petrophysical exploration data of boreholes and studying of rock core samples. The main feature of the present paper consists in the fact, that it involves three-dimensional saturated digital rock models, which were constructed based on the combined data considering microscopic structure of the porous media and the information about capillary equilibrium of oil-water mixture in pores. Data considering microscopic structure of the model are obtained by means of X-ray microscopic tomography. Information about distributions of saturating fluids is based on hydrodynamic simulations with density functional technique. In order to determine electromagnetic properties of the numerical model time-domain Fourier transform of Maxwell equations is considered. In low frequency approximation the problem can be reduced to solving elliptic equation for the distribution of complex electric potential. Finite difference approximation is based on discretization of the model with homogeneous isotropic orthogonal grid. This discretization implies that each computational cell contains exclusively one medium: water, oil or rock. In order to obtain suitable numerical model the distributions of saturating components is segmented. Such kind of modification enables avoiding usage of heterogeneous grids and disregards influence on the results of simulations of the additional techniques, required in order to determine properties of cells, filled with mixture of media. Corresponding system of differential equations is solved by means of biconjugate gradient stabilized method with multigrid preconditioner. Based on the results of complex electric potential computations average values of electrical conductivity and relative dielectric permittivity is calculated. For the sake of simplicity, this paper considers exclusively simulations with no spectral dependence of conductivities and permittivities of model components. The results of numerical simulations of spectral dependence of effective characteristics of heterogeneously saturated porous media (electrical conductivity and relative dielectric permittivity) in broad range of frequencies and multiple water saturations are represented in figures and table. Efficiency of the presented approach for determining spectral electrical properties of saturated rocks is discussed in conclusion.

The reentry vehicle of the transportation spacecraft that is being created by RSC Energia in regular mode makes soft landing on land surface using a parachute system and thruster devices. But in not standard situations the reentry vehicle also is capable of executing a splashdown. In that case, it becomes important to define the hydrodynamics impact on the reentry vehicle at the moment of the first contact with the surface of water and during submersion into water medium, and to study the dynamics of the vehicle behavior at more recent moments of time.

This article presents results of numerical studies of hydrodynamics forces on the conical vehicle during splashdown, done with the FlowVision software. The paper reviews the cases of the splashdown with inactive solid rocket motors on calm sea and the cases with interactions between rocket jets and the water surface. It presents data on the allocation of pressure on the vehicle in the process of the vehicle immersion into water medium and dynamics of the vehicle behavior after splashdown. The paper also shows flow structures in the area of the reentry vehicle at the different moments of time, and integral forces and moments acting on the vehicle.

For simulation process with moving interphases in the FlowVision software realized the model VOF (volume of fluid). Transfer of the phase boundary is described by the equation of volume fraction of this continuous phase in a computational cell. Transfer contact surface is described by the convection equation, and at the surface tension is taken into account by the Laplace pressure. Key features of the method is the splitting surface cells where data is entered the corresponding phase. Equations for both phases (like the equations of continuity, momentum, energy and others) in the surface cells are accounted jointly.

Efficiency of production directly depends on quality of the management of technology which, in turn, relies on the accuracy and efficiency of the processing of control and measuring information. Development of the mathematical methods of research of the system communications and regularities of functioning and creation of the mathematical models taking into account structural features of object of researches, and also writing of the software products for realization of these methods are an actual task. Practice has shown that the list of parameters that take place in the study of complex object of modern production, ranging from a few dozen to several hundred names, and the degree of influence of each factor in the initial time is not clear. Before working for the direct determination of the model in these circumstances, it is impossible — the amount of the required information may be too great, and most of the work on the collection of this information will be done in vain due to the fact that the degree of influence on the optimization of most factors of the original list would be negligible. Therefore, a necessary step in determining a model of a complex object is to work to reduce the dimension of the factor space. Most industrial plants are hierarchical group processes and mass volume production, characterized by hundreds of factors. (For an example of realization of the mathematical methods and the approbation of the constructed models data of the Moldavian steel works were taken in a basis.) To investigate the systemic linkages and patterns of functioning of such complex objects are usually chosen several informative parameters, and carried out their sampling. In this article the sequence of coercion of the initial indices of the technological process of the smelting of steel to the look suitable for creation of a mathematical model for the purpose of prediction is described. The implementations of new types became also creation of a basis for development of the system of automated management of quality of the production. In the course of weak correlation the following stages are selected: collection and the analysis of the basic data, creation of the table the correlated of the parameters, abbreviation of factor space by means of the correlative pleiads and a method of weight factors. The received results allow to optimize process of creation of the model of multiple-factor process.

Mathematical simulation of unsteady natural convection and thermal surface radiation within a rotating square enclosure was performed. The considered domain of interest had two isothermal opposite walls subjected to constant low and high temperatures, while other walls are adiabatic. The walls were diffuse and gray. The considered cavity rotated with constant angular velocity relative to the axis that was perpendicular to the cavity and crossed the cavity in the center. Mathematical model, formulated in dimensionless transformed variables “stream function – vorticity” using the Boussinesq approximation and diathermic approach for the medium, was performed numerically using the finite difference method. The vorticity dispersion equation and energy equation were solved using locally one-dimensional Samarskii scheme. The diffusive terms were approximated by central differences, while the convective terms were approximated using monotonic Samarskii scheme. The difference equations were solved by the Thomas algorithm. The approximated Poisson equation for the stream function was solved by successive over-relaxation method. Optimal value of the relaxation parameter was found on the basis of computational experiments. Radiative heat transfer was analyzed using the net-radiation method in Poljak approach. The developed computational code was tested using the grid independence analysis and experimental and numerical results for the model problem.

Numerical analysis of unsteady natural convection and thermal surface radiation within the rotating enclosure was performed for the following parameters: Ra = 10³–10⁶, Ta = 0–10⁵, Pr = 0.7, ε = 0–0.9. All distributions were obtained for the twentieth complete revolution when one can find the periodic behavior of flow and heat transfer. As a result we revealed that at low angular velocity the convective flow can intensify but the following growth of angular velocity leads to suppression of the convective flow. The radiative Nusselt number changes weakly with the Taylor number.

The work is dedicated to the use of the software package Turbulence Problem Solver (TPS) for numerical simulation of a wide range of laser problems. The capabilities of the package are demonstrated by the example of numerical simulation of the interaction of femtosecond laser pulses with thin metal bonds. The software package TPS developed by the authors is intended for numerical solution of hyperbolic systems of differential equations on multiprocessor computing systems with distributed memory. The package is a modern and expandable software product. The architecture of the package gives the researcher the opportunity to model different physical processes in a uniform way, using different numerical methods and program blocks containing specific initial conditions, boundary conditions and source terms for each problem. The package provides the the opportunity to expand the functionality of the package by adding new classes of problems, computational methods, initial and boundary conditions, as well as equations of state of matter. The numerical methods implemented in the software package were tested on test problems in one-dimensional, two-dimensional and three-dimensional geometry, which included Riemann's problems on the decay of an arbitrary discontinuity with different configurations of the exact solution.

Thin films on substrates are an important class of targets for nanomodification of surfaces in plasmonics or sensor applications. Many articles are devoted to this subject. Most of them, however, focus on the dynamics of the film itself, paying little attention to the substrate, considering it simply as an object that absorbs the first compression wave and does not affect the surface structures that arise as a result of irradiation. The paper describes in detail a computational experiment on the numerical simulation of the interaction of a single ultrashort laser pulse with a gold film deposited on a thick glass substrate. The uniform rectangular grid and the first-order Godunov numerical method were used. The presented results of calculations allowed to confirm the theory of the shock-wave mechanism of holes formation in the metal under femtosecond laser action for the case of a thin gold film with a thickness of about 50 nm on a thick glass substrate.

A hierarchical method of mathematical and computer modeling of interval-stochastic thermal processes in complex electronic systems for various purposes is developed. The developed concept of hierarchical structuring reflects both the constructive hierarchy of a complex electronic system and the hierarchy of mathematical models of heat exchange processes. Thermal processes that take into account various physical phenomena in complex electronic systems are described by systems of stochastic, unsteady, and nonlinear partial differential equations and, therefore, their computer simulation encounters considerable computational difficulties even with the use of supercomputers. The hierarchical method avoids these difficulties. The hierarchical structure of the electronic system design, in general, is characterized by five levels: Level 1 — the active elements of the ES (microcircuits, electro-radio-elements); Level 2 — electronic module; Level 3 — a panel that combines a variety of electronic modules; Level 4 — a block of panels; Level 5 — stand installed in a stationary or mobile room. The hierarchy of models and modeling of stochastic thermal processes is constructed in the reverse order of the hierarchical structure of the electronic system design, while the modeling of interval-stochastic thermal processes is carried out by obtaining equations for statistical measures. The hierarchical method developed in the article allows to take into account the principal features of thermal processes, such as the stochastic nature of thermal, electrical and design factors in the production, assembly and installation of electronic systems, stochastic scatter of operating conditions and the environment, non-linear temperature dependencies of heat exchange factors, unsteady nature of thermal processes. The equations obtained in the article for statistical measures of stochastic thermal processes are a system of 14 non-stationary nonlinear differential equations of the first order in ordinary derivatives, whose solution is easily implemented on modern computers by existing numerical methods. The results of applying the method for computer simulation of stochastic thermal processes in electron systems are considered. The hierarchical method is applied in practice for the thermal design of real electronic systems and the creation of modern competitive devices.