All issues

The article describes an improved paired comparison method, which systematizes in tables the rules of logical conclusions and formulas of checking indices for comparison of technical systems. To achieve this goal, the authors formulate rational rules of logical conclusions in making a paired comparison of the systems. In addition, for the purpose of consistency check of the results of the assessment, the authors introduce parameters such as «the number of scores gained by one system» and «systems’ quality index»; moreover, they design corresponding calculation formulas. For the purposes of practical application of this method to design computer programs, the authors propose to use formalized variants of interconnected tables: a table for processing and systematization of expert information, a table of possible logical conclusions based on the results of comparison of a set number of technical systems and a table of check values in the paired comparison method used in quality assessment of a definite number of technical systems. These tables allow one to organize procedures of the information processing in a more rational way and to predominantly exclude the influence of mistakes on the results of quality assessment of technical systems at the stage of data input. The main positive effect from the implementation of the paired comparison method is observed in a considerable reduction of time and resources needed to organize experts work, process expert information, and to prepare and conduct distant interviews with experts (on the Internet or a local computer network of an organization). This effect is achieved by a rational use of input data of the quality of the systems to be assessed. The proposed method is applied to computer programs used in assessing the effectiveness and stability of large technical systems.

The paper presents the results of numerical simulation of different-temperature water flows turbulent mixing in a T-junctions in the FlowVision software package. The article describes in detail an experimental stand specially designed to obtain boundary conditions that are simple for most computational fluid dynamics software systems. Values of timeaveraged temperatures and velocities in the control sensors and planes were obtained according to the test results. The article presents the system of partial differential equations used in the calculation describing the process of heat and mass transfer in a liquid using the Smagorinsky turbulence model. Boundary conditions are specified that allow setting the random velocity pulsations at the entrance to the computational domain. Distributions of time-averaged water velocity and temperature in control sections and sensors are obtained. The simulation is performed on various computational grids, for which the axes of the global coordinate system coincide with the directions of hot and cold water flows. The possibility for FlowVision PC to construct a computational grid in the simulation process based on changes in flow parameters is shown. The influence of such an algorithm for constructing a computational grid on the results of calculations is estimated. The results of calculations on a diagonal grid using a beveled scheme are given (the direction of the coordinate lines does not coincide with the direction of the tee pipes). The high efficiency of the beveled scheme is shown when modeling flows whose general direction does not coincide with the faces of the calculated cells. A comparison of simulation results on various computational grids is carried out. The numerical results obtained in the FlowVision PC are compared with experimental data and calculations performed using other computing programs. The results of modeling turbulent mixing of water flow of different temperatures in the FlowVision PC are closer to experimental data in comparison with calculations in CFX ANSYS. It is shown that the application of the LES turbulence model on relatively small computational grids in the FlowVision PC allows obtaining results with an error within 5%.

Computer-aided assembly planning of complex products is an important area of modern information technology. The sequence of assembly and decomposition of the product into assembly units largely depend on the mechanical structure of a technical system (machine, mechanical device, etc.). In most modern research, the mechanical structure of products is modeled using a graph of connections and its various modifications. The coordination of parts during assembly can be achieved by implementing several connections at the same time. This generates a $k$-ary basing relation on a set of product parts, which cannot be correctly described by graph means. A hypergraph model of the mechanical structure of a product is proposed. Modern discrete manufacturing uses sequential coherent assembly operations. The mathematical description of such operations is the normal contraction of edges of the hypergraph model. The sequence of contractions that transform the hypergraph into a point is a description of the assembly plan. Hypergraphs for which such a transformation exists are called $s$-hypergraphs. $S$-hypergraphs are correct mathematical models of the mechanical structures of any assembled products. A theorem on necessary conditions for the contractibility of $s$-hypergraphs is given. It is shown that the necessary conditions are not sufficient. An example of a noncontractible hypergraph for which the necessary conditions are satisfied is given. This means that the design of a complex technical system may contain hidden structural errors that make assembly of the product impossible. Therefore, finding sufficient conditions for contractibility is an important task. Two theorems on sufficient conditions for contractibility are proved. They provide a theoretical basis for developing an efficient computational procedure for finding all $s$-subgraphs of an $s$-hypergraph. An $s$-subgraph is a model of any part of a product that can be assembled independently. These are, first of all, assembly units of various levels of hierarchy. The set of all $s$-subgraphs of an $s$-hypergraph, ordered by inclusion, is a lattice. This model can be used to synthesize all possible sequences of assembly and disassembly of a product and its components. The lattice model of the product allows you to analyze geometric obstacles during assembly using algebraic means.

In this paper, we propose a new software for simulation of fluid-structure interaction. The software is designed for solving coupled problems and provides an interface for synchronization synchronisation and data exchange between existing fluid and structural solvers. Algorithms of coupling solvers and mesh deformation are discussed. The software can be used on hybrid CPU/GPU platforms.

It is discussed peculiarities of forming gas temperature fields in gas turbine engine low emission combustors. It is shown the influence of burn-up rate on combustor outlet temperature and proposed recommendation for design the dilution system for the combustor.

The article presents a method for linearization the effective function of material instantaneous deformation in order to generalize the torsional vibration equation to the case of nonlinearly deformable rheologically active shafts. It is considered layered and structurally heterogeneous, on average isotropic shafts made of nonlinearly viscoelastic components. The technique consists in determining the approximate shear modulus by minimizing the root-mean-square deviation in approximation of the effective diagram of instantaneous deformation.

The method allows to estimate analytically values of natural frequencies of layered and structurally heterogeneous nonlinearly viscoelastic shaft. This makes it possible to significantly reduce resources in vibration analysis, as well as to track changes in values of natural frequencies with changing geometric, physico-mechanical and structural parameters of shafts, which is especially important at the initial stages of modeling and design. In addition, the paper shows that only a pronounced nonlinearity of the effective state equation has an effect on the natural frequencies, and in some cases the nonlinearity in determining the natural frequencies can be neglected.

As equations of state of the composite material components, the article considers the equations of nonlinear heredity with instantaneous deformation functions in the form of the Prandtl’s bilinear diagrams. To homogenize the state equations of layered shafts, it is applied the Voigt’s hypothesis on the homogeneity of deformations and the Reuss’ hypothesis on the homogeneity of stresses in the volume of a composite body. Using these assumptions, effective secant and tangential shear moduli, proportionality limits, as well as creep and relaxation kernels of longitudinal, axial and transversely layered shafts are obtained. In addition, it is obtained the indicated effective characteristics of a structurally heterogeneous, on average isotropic shaft using the homogenization method previously proposed by the authors, based on the determination of the material deformation parameters by the rule of a mixture for the Voigt’s and the Reuss’ state equations.

A hierarchical method of mathematical and computer modeling of interval-stochastic thermal processes in complex electronic systems for various purposes is developed. The developed concept of hierarchical structuring reflects both the constructive hierarchy of a complex electronic system and the hierarchy of mathematical models of heat exchange processes. Thermal processes that take into account various physical phenomena in complex electronic systems are described by systems of stochastic, unsteady, and nonlinear partial differential equations and, therefore, their computer simulation encounters considerable computational difficulties even with the use of supercomputers. The hierarchical method avoids these difficulties. The hierarchical structure of the electronic system design, in general, is characterized by five levels: Level 1 — the active elements of the ES (microcircuits, electro-radio-elements); Level 2 — electronic module; Level 3 — a panel that combines a variety of electronic modules; Level 4 — a block of panels; Level 5 — stand installed in a stationary or mobile room. The hierarchy of models and modeling of stochastic thermal processes is constructed in the reverse order of the hierarchical structure of the electronic system design, while the modeling of interval-stochastic thermal processes is carried out by obtaining equations for statistical measures. The hierarchical method developed in the article allows to take into account the principal features of thermal processes, such as the stochastic nature of thermal, electrical and design factors in the production, assembly and installation of electronic systems, stochastic scatter of operating conditions and the environment, non-linear temperature dependencies of heat exchange factors, unsteady nature of thermal processes. The equations obtained in the article for statistical measures of stochastic thermal processes are a system of 14 non-stationary nonlinear differential equations of the first order in ordinary derivatives, whose solution is easily implemented on modern computers by existing numerical methods. The results of applying the method for computer simulation of stochastic thermal processes in electron systems are considered. The hierarchical method is applied in practice for the thermal design of real electronic systems and the creation of modern competitive devices.

Disclosed is a multidimensional nodal method of characteristics, designed to integrate hyperbolic systems, based on splitting the initial system of equations into a number of one-dimensional subsystems, for which a onedimensional nodal method of characteristics is used. Calculation formulas are given, the calculation method is described in detail in relation to a single-speed model of a heterogeneous medium in the presence of gravity forces. The presented method is applicable to other hyperbolic systems of equations. Using this explicit, nonconservative, first-order accuracy of the method, a number of test tasks are calculated and it is shown that in the framework of the proposed approach, by attracting additional points in the circuit template, it is possible to carry out calculations with Courant numbers exceeding one. So, in the calculation of the flow of the threedimensional step by the flow of a heterogeneous mixture, the Courant number was 1.2. If Godunov’s method is used to solve the same problem, the maximum number of Courant, at which a stable account is possible, is 0.13 × 10^-2. Another feature of the multidimensional method of characteristics is the weak dependence of the time step on the dimension of the problem, which significantly expands the possibilities of this approach. Using this method, a number of problems were calculated that were previously considered “heavy” for the numerical methods of Godunov, Courant – Isaacson – Rees, which is due to the fact that it most fully uses the advantages of the characteristic representation of the system of equations.

The work is devoted to the structural analysis of complex technical systems. Mechanical structures are considered, the properties of which affect the behavior of products during assembly, repair and operation. The main source of data on parts and mechanical connections between them is a hypergraph. This model formalizes the multidimensional basing relation. The hypergraph correctly describes the connectivity and mutual coordination of parts, which is achieved during the assembly of the product. When developing complex products in CAD systems, an engineer often makes serious design mistakes: overbasing of parts and non-sequential assembly operations. Effective ways of identifying these structural defects have been proposed. It is shown that the property of independent assembly can be represented as a closure operator whose domain is the boolean of the set of product parts. The images of this operator are connected and coordinated subsets of parts that can be assembled independently. A lattice model is described, which is the state space of the product during assembly, disassembly and decomposition into assembly units. The lattice model serves as a source of various structural information about the project. Numerical estimates of the cardinality of the set of admissible alternatives in the problems of choosing an assembly sequence and decomposition into assembly units are proposed. For many technical operations (for example, control, testing, etc.), it is necessary to mount all the operand parts in one assembly unit. A simple formalization of the technical conditions requiring the inclusion (exclusion) of parts in the assembly unit (from the assembly unit) has been developed. A theorem that gives an mathematical description of product decomposition into assembly units in exact lattice terms is given. A method for numerical evaluation of the robustness of the mechanical structure of a complex technical system is proposed.

The paper presents a mathematical model to be used for design of cooling tanks for vapor desublimation. Results of calculations for the process of cooling of two tanks in a block of four are presented. Chart of the cooling air flow in the piping network is presented.