All issues

A variant of import into ANSYS Mechanical APDL system of the model of behavior of flexible woven composite materials with reinforcing weaving cloth of linen at static stretching along the reinforcement yarns is offered. The import was carried out using an integration module based on the use of an analytical model of deformation of the material under study. The model is presented in the articles published earlier and takes into account the changes in the geometric structure occurring in the reinforcing layer of the material during the deformation process, the formation of irreversible deformations and the interaction of cross-lying reinforcing fabric threads. In the introduction input characteristics of the plain weave of the reinforcing fabric and the analytical model imported into ANSYS are briefly described. The input parameters of the module are the mechanical characteristics of the materials that make up the composite (binder and material of reinforcement yarns), the geometric characteristics of the interlacing of the reinforcing fabric. The algorithm for importing the model is based on the calculation and transfer in ANSYS of the calculated points of the material stress-strain diagram for uniaxial stretching along the reinforcement direction and using the Multilinear Kinematich Hardening model material embedded in the ANSYS. The analytical model imported with the help of the presented module allows to model a composite material with reinforcing fabric without a detailed description of the geometry of the interlacing of threads during modeling of the material as a whole. The imported model was verified. For verification full-scale experimental studies and numerical simulation of the stretching of samples from flexible woven composites were carried out. The analysis of the obtained results showed good qualitative and quantitative agreement of calculations.

At present, the accelerator complex NICA is being built at JINR (Dubna). It is intended for performing experiments to study interactions of relativistic nuclei and polarized particles (protons and deuterons). One of the experimental facilitues MPD (MultiPurpose Detector) was designed to investigate nucleus-nucleus, protonnucleus and proton-proton interactions. The existing plans of future MPD upgrade consider a possibility to install an inner tracker made of the new generation silicon pixel sensors. It is expected that such a detector will considerably enhance the research capability of the experiment both for nucleus-nucleus interactions (due to a high spatial resolution near the collision region) and proton-proton ones (due to a fast detector response).

This paper presents main characteristics of such a tracker, obtained using a Monte-Carlo simulation of the detector for proton-proton collisions. In particular, the detector ability to reconstruct decay vertices of short-lived particles and perform a selection of rare events of such decays from much more frequent “common” interactions are evaluated. Also, the problem of a separation of multiple collisions during the high luminosity accelerator running and the task of detector triggering on rare events are addressed. The results obtained can be used to justify the necessity to build such a detector and to develop a high-level trigger system, possibly based on machine learning techniques.

The paper studies the determination for one of the dynamic quality parameter (PDK) of railway vehicles — car body lateral acceleration — by using of computer simulation system for railway vehicles dynamic Simpack Rail. This provide the complex simulation environment with variable velocity depending on the train schedule. The rail vehicle model of typical 1520 mm gauge fright locomotive section used for simulation has been verified by means of the chair “Electric multiple unit cars and locomotives” in the Russian University of Transport (RUT (MIIT)). Due to this homologation the questions of model creating and verification in preprocessor are excluded in this paper. The paper gives the detail description of cartographic track modeling in situation plane, heights plane and superelevation plane based on the real operating data. The statistic parameters (moments) for the rail related track excitation and used cartographic track data of the specified track section in this simulation are given as a numeric and graphical results of reading the prepared data files. The measurement of the car body residual lateral acceleration occur under consideration of the earth gravity acceleration part like the accelerometer measurement in the real world. Finally the desired quality parameter determined by simulation is compared with the same one given by a test drive. The calculation method in both cases is based on the middle value of the absolute maximums picked up within the nonstationary realizations of this parameter. Compared results confirm that this quality factor all the first depends on the velocity and track geometry properties. The simulation of the track in this application uses the strong conformity original track data of the test ride track section. The accepted simplification in the rail vehicle model of fright electric locomotive section (body properties related to the center of gravity, small displacements between the bodies) by keeping the geometric and force law characteristics of the force elements and constraints constant allow in Simpack Rail the simulation with necessary validity of system behavior (reactions).

The paper presents the results of numerical simulation of the effect of a long spark discharge on the mixing dynamics of an injected gas jet with supersonic air flow. The calculations were performed using the CFD software package FlowVision. The fuel was supplied using an injector located on the channel wall, and the discharge was organized near the wall downstream of the injector. Simulation of electrical spark discharge was performed using a volumetric heat source. In order to describe the principal specifications of a plasma actuator to accelerate mixing in a supersonic flow (Mach number M = 2), the research involved varying the energy impact to the discharge in the range of 100–500 mJ per pulse, determining the influence of the shape and location of the discharge. A study of the fuel injection modes in a supersonic air flow has been carried out and an optimal gas jet outflow regime has been found to study the effect of a spark discharge. A method has been developed for analyzing the disturbance pattern of the fuel-oxidant interface caused by the operation of a pulsed spark discharge. A program was prepared in the LabView software environment for obtaining quantitative characteristics for further comparison with the results obtained in the experiment.

The simulation results allow us to conclude that the long spark discharge located along the flow downstream of the injector provides the maximum increase in the interface between the jet of fuel and the main flow. A typical repetition frequency of discharge pulses in a pulse-periodic mode should be more than 6 kHz with a discharge length of ~10 mm to ensure a continuous effect on the mixing at a flow velocity of 500 m/s.

While modeling seismic wave propagation, it is important to take into account nontrivial topography, as this topography causes multiple complex phenomena, such as diffraction at rough surfaces, complex propagation of Rayleigh waves, and side effects caused by wave interference. The primary goal of this research is to construct a method that implements the free surface on topography, utilizing an overset curved grid for characterization, while keeping the main grid structured rectangular. For a combination of the regular and curve-linear grid, the workability of the grid characteristics method using overset grids (also known as the Chimera grid approach) is analyzed. One of the benefits of this approach is computational complexity reduction, caused by the fact that simulation in a regular, homogeneous physical area using a sparse regular rectangle grid is simpler. The simplification of the mesh building mechanism (one grid is regular, and the other can be automatically built using surface data) is a side effect. Despite its simplicity, the method we propose allows us to increase the digitalization of fractured regions and minimize the Courant number. This paper contains various comparisons of modeling results produced by the proposed method-based solver, and results produced by the well-known solver specfem2d, as well as previous modeling results for the same problems. The drawback of the method is that an interpolation error can worsen an overall model accuracy and reduce the computational schema order. Some countermeasures against it are described. For this paper, only two-dimensional models are analyzed. However, the method we propose can be applied to the three-dimensional problems with minimal adaptation required.

The paper provides the mathematical and numerical models of the interrelated thermo- and hydrodynamic processes in the operational mode of development the unified oil-producing complex during the hydrogel flooding of the non-uniform oil reservoir exploited with a system of arbitrarily located injecting wells and producing wells equipped with submersible multistage electrical centrifugal pumps. A special feature of our approach is the modeling of the special ground-based equipment operation (control stations of submersible pumps, drossel devices on the head of producing wells), designed to regulate the operation modes of both the whole complex and its individual elements.

The complete differential model includes equations governing non-stationary two-phase five-component filtration in the reservoir, quasi-stationary heat and mass transfer in the wells and working channels of pumps. Special non-linear boundary conditions and dependencies simulate, respectively, the influence of the drossel diameter on the flow rate and pressure at the wellhead of each producing well and the frequency electric current on the performance characteristics of the submersible pump unit. Oil field development is also regulated by the change in bottom-hole pressure of each injection well, concentration of the gel-forming components pumping into the reservoir, their total volume and duration of injection. The problem is solved numerically using conservative difference schemes constructed on the base of the finite difference method, and developed iterative algorithms oriented on the parallel computing technologies. Numerical model is implemented in a software package which can be considered as the «Intellectual System of Wells» for the virtual control the oil field development.

Flexible woven composites are classified as high-tech innovative materials. Due to the combination of various components of the filler and reinforcement elements, such materials are used in construction, in the defense industry, in shipbuilding and aircraft construction, etc. In the domestic literature, insufficient attention is paid to woven composites that change their geometric structure of the reinforcing layer during deformation. This paper presents an analysis of the previously proposed complex approach to modeling the behavior of flexible woven composites under static uniaxial tension for further generalization of the approach to biaxial tension. The work is aimed at qualitative and quantitative description of mechanical deformation processes occurring in the structure of the studied materials under tension, which include straightening the strands of the reinforcing layer and increasing the value of mutual pressure of the cross-lying reinforcement strands. At the beginning of the deformation process, the straightening of the threads and the increase in mutual pressure of the threads are most intense. With the increase in the level of load, the change of these parameters slows down. For example, the bending of the reinforcement strands goes into the Central tension, and the value of the load from the mutual pressure is no longer increased (tends to constant). To simulate the described processes, the basic geometrical and mechanical parameters of the material affecting the process of forming are introduced, the necessary terminology and description of the characteristics are given. Due to the high geometric nonlinearity of the all processes described in the increments, as in the initial load values there is a significant deformation of the reinforcing layer. For the quantitative and qualitative description of mechanical deformation processes occurring in the reinforcing layer, analytical dependences are derived to determine the increment of the angle of straightening of reinforcement filaments and the load caused by the mutual pressure of the cross-lying filaments at each step of the load increment. For testing of obtained dependencies shows an example of their application for flexible woven composites brands VP4126, VP6131 and VP6545. The simulation results confirmed the assumptions about the processes of straightening the threads and slowing the increase in mutual pressure of the threads. The results and dependences presented in this paper are directly related to the further generalization of the previously proposed analytical models for biaxial tension, since stretching in two directions will significantly reduce the straightening of the threads and increase the amount of mutual pressure under similar loads.

The paper describes an analytical study of hydrodynamic processes taking place in the course of coolant flow through a fuel assembly of the core of a fast neutron sodium-cooled reactor. Within the framework of the study, a procedure and an analytical model were developed based on program complex FlowVision of computational fluid dynamics, which, using proved simplifications, permits to obtain a coefficient of rod lifting margin of a fuel assembly and to study hydrodynamic characteristics of processes taking place in the course of simulation of different initial events influencing motion of a reactor core fuel assembly.

For analytical justification a fuel assembly model was developed, which is equivalent by hydraulic resistance values and permits not to simulate explicitly a complicated full-scale fuel assembly design, thus, decreasing a number of computational cells in the model and, as a result, reducing computational and time resources.

Hydraulic parameters of the equivalent fuel assembly model in program complex FlowVision were analyzed in two stages. At the first stage, to determine the minimum rod lifting margin coefficient of a fuel assembly, steady-state analyses were performed, where various flowrate values were assigned at the model inlet and forces acting upon the assembly were analyzed. A series of dynamic mode analyses was performed at the second stage. Jump-like pressure increase being the initial event which could occur hypothetically in the fast neutron sodium cooled reactor plant was assigned in these modes. Hydrodynamic parameters and forces acting upon the fuel assembly were determined.

The results of the first stage of the analytical study proved the minimum coefficient of rod lifting margin of a fuel assembly of the fast neutron reactor justified in reactor plant design documentation. As a result of the second stage of the study, conclusions were made on impossibility for the fuel assembly to move at the initial event associated with jump-like pressure increase in the reactor pressure chamber.

The main feature of a two-dimensional turbulent flow, constantly excited by an external force, is the appearance of an inverse energy cascade. Due to nonlinear effects, the spatial scale of the vortices created by the external force increases until the growth is stopped by the size of the cell. In the latter case, energy is accumulated at these dimensions. Under certain conditions, accumulation leads to the appearance of a system of coherent vortices. The observed vortices are of the order of the box size and, on average, are isotropic. Numerical simulation is an effective way to study such the processes. Of particular interest is the problem of studying the viscous fluid turbulence in a square cell under excitation by short-wave and long-wave static external forces. Numerical modeling was carried out with a weakly compressible fluid in a two-dimensional square cell with zero boundary conditions. The work shows how the flow characteristics are influenced by the spatial frequency of the external force and the magnitude of the viscosity of the fluid itself. An increase in the spatial frequency of the external force leads to stabilization and laminarization of the flow. At the same time, with an increased spatial frequency of the external force, a decrease in viscosity leads to the resumption of the mechanism of energy transfer along the inverse cascade due to a shift in the energy dissipation region to a region of smaller scales compared to the pump scale.

The gradual incorporation of automated vehicles into the global transport networks leads to the need to develop tools to assess the impact of this process on various aspects of traffic. This implies a more organized movement of automated vehicles which can form uniformly moving platoons. The influence of the formation and movement of these platoons on the dynamics of traffic flow is of great interest. The currently most developed traffic flow models are based on the cellular automaton approach. They are mainly developed in the direction of increasing accuracy. This inevitably leads to the complication of models, which in their modern form have significantly moved away from the original philosophy of cellular automata, which implies simplicity and schematicity of models at the level of evolution rules, leading, however, to a complex organized behavior of the system. In the present paper, a simulation model of connected automated vehicles platoon dynamics in a heterogeneous transport system is proposed, consisting of two types of agents (vehicles): human-driven and automated. The description of the temporal evolution of the system is based on modified rules 184 and 240 for elementary cellular automata. Human-driven vehicles move according to rule 184 with the addition of accidental braking, the probability of which depends on the distance to the vehicle in front. For automated vehicles, a combination of rules is used depending on the type of nearest neighbors, regardless of the distance to them, which brings non-local interaction to the model. At the same time, it is considered that a group of sequentially moving connected automated vehicles can form an organized platoon. The influence of the ratio of types of vehicles in the system on the characteristics of the traffic flow during free movement on a circular one-lane and two-lane roads, as well as in the presence of a traffic light, is studied. The simulation results show that the effect of platoon formation is significant for a freeway traffic flow; the presence of a traffic light reduces the positive effect by about half. The movement of platoons of connected automated vehicles on two-lane roads with the possibility of lane changing was also studied. It is shown that considering the types of neighboring vehicles (automated or human-driven) when changing lanes for automated vehicles has a positive effect on the characteristics of the traffic flow.