All issues

A mathematical model of two-phase capillary-nonequilibrium isothermal flows of incompressible phases in a double porosity medium is constructed. A double porosity medium is considered, which is a composition of two porous media with contrasting capillary properties (absolute permeability, capillary pressure). One of the constituent media has high permeability and is conductive, the second is characterized by low permeability and forms an disconnected system of matrix blocks. A feature of the model is to take into account the influence of capillary nonequilibrium on mass transfer between subsystems of double porosity, while the nonequilibrium properties of two-phase flow in the constituent media are described in a linear approximation within the Hassanizadeh model. Homogenization by the method of formal asymptotic expansions leads to a system of partial differential equations, the coefficients of which depend on internal variables determined from the solution of cell problems. Numerical solution of cell problems for a system of partial differential equations is computationally expensive. Therefore, a thermodynamically consistent kinetic equation is formulated for the internal parameter characterizing the phase distribution between the subsystems of double porosity. Dynamic relative phase permeability and capillary pressure in the processes of drainage and impregnation are constructed. It is shown that the capillary nonequilibrium of flows in the constituent subsystems has a strong influence on them. Thus, the analysis and modeling of this factor is important in transfer problems in systems with double porosity.

Safe carrying out of emergency recovery operations at emergency offshore gas condensate wells is possible when taking into account the hazardous factors that prevent anti-fontanning measures. One of such factors is the gassiness of the operation zone due to the release from the water column of a large amount of light, as compared to air, natural gas, as well as vapours of heavier components of gas condensate. To estimate the distribution of explosive concentration of petroleum product vapours in the near surface layer of the atmosphere, it is necessary to determine the characteristics of the source of the contamination. Based on the analysis of theoretical works concerning to the formation of the velocity field in the upper layer of the sea as a result of large amounts of gas coming to the surface, an analytical model is proposed to calculate the size of the area in which a significant amount of gas condensate coming to the surface is vaporised during accidents at shallow-water wells. The stationary regime of reservoir fluid flow during fountaining of offshore gas and oil wells with an underwater location of their mouths is considered. A low-parametric model of oil product evaporation from films of different thickness is constructed. It is shown that the size of the zone of intensive evaporation at shallow-water wells is determined by the volume flow of liquid fraction, its fractional composition and selected threshold for estimation of oil product vapour flow into the atmosphere. In the context of this work shallow water wells are wells with gas flow rate from 1 to 20 million cubic meters at sea depths of about 50–200 metres. In this case, the formation fluid jet from the wellhead on the seabed is transformed into a bubble plume, the stratification of the water column, typical for the summer-autumn period, does not limit the plume’s exit to the sea surface, and the velocity of bubble rise allows the gas dissolution process to be disregardded. The analysis was limited to almost calm hydrometeorological conditions. Such conditions are favourable for offshore operations, but unfavourable from the point of view of dispersion of high concentrations of oil product vapours in the near surface layer of the atmosphere. As a result of this work, an analytical dependence for an approximate assessment of the zone of intensive evaporation of gas condensate is proposed.

In the paper, it is represented a linearization method for the stress-strain curves of nonlinearly deformable beams and circular plates in order to generalize the pure bending vibration equations. It is considered composite, on average isotropic prismatic beams of a constant rectangular cross-section and circular plates of a constant thickness made of nonlinearly elastic materials. The technique consists in determining the approximate Young’s moduli from the initial stress-strain state of beam and plate subjected to the action of the bending moment.

The paper proposes two criteria for linearization: the equality of the specific potential energy of deformation and the minimization of the standard deviation in the state equation approximation. The method allows obtaining in the closed form the estimated value of the natural frequencies of layered and structurally heterogeneous, on average isotropic nonlinearly elastic beams and circular plates. This makes it possible to significantly reduce the resources in the vibration analysis and modeling of these structural elements. In addition, the paper shows that the proposed linearization criteria allow to estimate the natural frequencies with the same accuracy.

Since in the general case even isotropic materials exhibit different resistance to tension and compression, it is considered the piecewise-linear Prandtl’s diagrams with proportionality limits and tangential Young’s moduli that differ under tension and compression as the stress-strain curves of the composite material components. As parameters of the stress-strain curve, it is considered the effective Voigt’s characteristics (under the hypothesis of strain homogeneity) for a longitudinally layered material structure; the effective Reuss’ characteristics (under the hypothesis of strain homogeneity) for a transversely layered beam and an axially laminated plate. In addition, the effective Young’s moduli and the proportionality limits, obtained by the author’s homogenization method, are given for a structurally heterogeneous, on average isotropic material. As an example, it is calculated the natural frequencies of two-phase beams depending on the component concentrations.

This article discusses the mechanical properties of carbon nanotube (CNT)-reinforced platinum under uniaxial tensile loading using the molecular dynamics method. A review of current computational and experimental studies on the use of carbon nanotube-reinforced composites from a structural point of view. However, quantitative and qualitative studies of CNTs to improve the properties of composites are still rare. Composite selection is a promising application for platinum alloys in many cases where they may be subjected to mechanical stress, including in biocompatibility sources. Pt-reinforced with CNTs may have additional possibilities for implantation of the implant and at the same time obtain the required mechanical characteristics.

The structure of the composite is composed of a Pt crystal with a face-centered cubic lattice with a constant of 3.92 Å and a carbon nanotube. The Pt matrix has the shape of a cube with dimensions of $43.1541 Å \times 43.1541 Å \times 43.1541 Å$. The hole size in the average platinum dimension is the radius of the carbon nanotube of the «zigzag» type (8,0), which is 2.6 Å. A carbon nanotube is placed in a hole with a radius of 4.2 Å. At such parameters, the maximum energy level was mutually observed. The model under consideration is contained in 320 atomic bombs and 5181 atomic platinum. The volume fraction of deaths in the Pt-C composite is 5.8%. At the first stage of the study, the strain rate was analyzed for stress-strain and energy change during uniaxial action on the Pt-C composite.

Analysis of the strain rate study showed that the consumption yield strength increases with high strain rate, and the elasticity has increased density with decreasing strain rate. This work also increased by 40% for Pt-C, the elasticity of the composite decreased by 42.3%. In general, fracture processes are considered in detail, including plastic deformation on an atomistic scale.

We propose a three-component discrete-time model of the phytoplankton-zooplankton community, in which toxic and non-toxic species of phytoplankton compete for resources. The use of the Holling functional response of type II allows us to describe an interaction between zooplankton and phytoplankton. With the Ricker competition model, we describe the restriction of phytoplankton biomass growth by the availability of external resources (mineral nutrition, oxygen, light, etc.). Many phytoplankton species, including diatom algae, are known not to release toxins if they are not damaged. Zooplankton pressure on phytoplankton decreases in the presence of toxic substances. For example, Copepods are selective in their food choices and avoid consuming toxin-producing phytoplankton. Therefore, in our model, zooplankton (predator) consumes only non-toxic phytoplankton species being prey, and toxic species phytoplankton only competes with non-toxic for resources.

We study analytically and numerically the proposed model. Dynamic mode maps allow us to investigate stability domains of fixed points, bifurcations, and the evolution of the community. Stability loss of fixed points is shown to occur only through a cascade of period-doubling bifurcations. The Neimark – Sacker scenario leading to the appearance of quasiperiodic oscillations is found to realize as well. Changes in intrapopulation parameters of phytoplankton or zooplankton can lead to abrupt transitions from regular to quasi-periodic dynamics (according to the Neimark – Sacker scenario) and further to cycles with a short period or even stationary dynamics. In the multistability areas, an initial condition variation with the unchanged values of all model parameters can shift the current dynamic mode or/and community composition.

The proposed discrete-time model of community is quite simple and reveals dynamics of interacting species that coincide with features of experimental dynamics. In particular, the system shows behavior like in prey-predator models without evolution: the predator fluctuations lag behind those of prey by about a quarter of the period. Considering the phytoplankton genetic heterogeneity, in the simplest case of two genetically different forms: toxic and non-toxic ones, allows the model to demonstrate both long-period antiphase oscillations of predator and prey and cryptic cycles. During the cryptic cycle, the prey density remains almost constant with fluctuating predators, which corresponds to the influence of rapid evolution masking the trophic interaction.

The study of the structural characteristics of composites and nanostructures is of fundamental importance in materials science. Theoretical and numerical modeling and simulation of the mechanical properties of nanostructures is the main tool that allows for complex studies that are difficult to conduct only experimentally. One example of nanostructures considered in this work are carbon nanotubes (CNTs), which have good thermal and electrical properties, as well as low density and high Young’s modulus, making them the most suitable reinforcement element for composites, for potential applications in aerospace, automotive, metallurgical and biomedical industries. In this review, we reviewed the modeling methods, mechanical properties, and applications of CNT-reinforced metal matrix composites. Some modeling methods applicable in the study of composites with polymer and metal matrices are also considered. Methods such as the gradient descent method, the Monte Carlo method, methods of molecular statics and molecular dynamics are considered. Molecular dynamics simulations have been shown to be excellent for creating various composite material systems and studying the properties of metal matrix composites reinforced with carbon nanomaterials under various conditions. This paper briefly presents the most commonly used potentials that describe the interactions of composite modeling systems. The correct choice of interaction potentials between parts of composites directly affects the description of the phenomenon being studied. The dependence of the mechanical properties of composites on the volume fraction of the diameter, orientation, and number of CNTs is detailed and discussed. It has been shown that the volume fraction of carbon nanotubes has a significant effect on the tensile strength and Young’s modulus. The CNT diameter has a greater impact on the tensile strength than on the elastic modulus. An example of works is also given in which the effect of CNT length on the mechanical properties of composites is studied. In conclusion, we offer perspectives on the direction of development of molecular dynamics modeling in relation to metal matrix composites reinforced with carbon nanomaterials.

The physical and mathematical model of combustion of the polydisperse suspension of coal dust was developed. The formulation of the problem takes into account the evaporation of particle volatile components during the heating, the particle emitting and the gas heat transfer to a surrounding area via the sphere volume side surface, heat transfer coefficient as a function of temperature. The polydisperse of coal-dust is taken into consideration. N — the number of fraction. Fractions are subdivided into inert and reacting particles. The oxidizer mass balance equation takes into consideration the oxidizer consumption per each reaction (heterogeneous on the particle surface and homogenous in the gas). Exothermic chemical reactions in gas are determined by Arrhenius equation with second-order kinetics. The heterogeneous reaction on the particle surface was first-order reaction. The numerical simulation was solved by Runge–Kutta–Merson method. Reliability of the calculations was verified by solving the partial problems. During the numerical calculation the percentage composition of inert and reacting particles in coal-dust and their total mass were changed for each simulation. We have determined the influence of the percentage composition of inert and reacting particles on burning characteristics of polydisperse coal-dust methane-air mixture. The results showed that the percent increase of volatile components in the mixture lead to the increase of total pressure in the volume. The value of total pressure decreases with the increasing of the inert components in the mixture. It has been determined that there is the extremism radius value of coarse particles by which the maximum pressure reaches the highest value.

In this paper, we develop a new first-order method for composite nonconvex minimization problems with simple constraints and inexact oracle. The objective function is given as a sum of «hard», possibly nonconvex part, and «simple» convex part. Informally speaking, oracle inexactness means that, for the «hard» part, at any point we can approximately calculate the value of the function and construct a quadratic function, which approximately bounds this function from above. We give several examples of such inexactness: smooth nonconvex functions with inexact H¨older-continuous gradient, functions given by the auxiliary uniformly concave maximization problem, which can be solved only approximately. For the introduced class of problems, we propose a gradient-type method, which allows one to use a different proximal setup to adapt to the geometry of the feasible set, adaptively chooses controlled oracle error, allows for inexact proximal mapping. We provide a convergence rate for our method in terms of the norm of generalized gradient mapping and show that, in the case of an inexact Hölder-continuous gradient, our method is universal with respect to Hölder parameters of the problem. Finally, in a particular case, we show that the small value of the norm of generalized gradient mapping at a point means that a necessary condition of local minimum approximately holds at that point.

The article gives the example of finite-element modeling of the structural element is a flexible woven composites. The reinforcing cloth is a plain weave of threads of assembled harness. Threads are represented by elastic material. The matrix of the material is a soft polymer with the possibility of irreversible deformations. Taken into account the possibility of the occurrence of damage in the structure of the material under high loads. Built detailed diagram of deformation under uniaxial tension. The accuracy of the model is conrmed by in situ experiments.

The paper contains numerical simulation of nonisothermal nonlinear flow in a porous medium. Twodimensional unsteady problem of heavy oil, water and steam flow is considered. Oil phase consists of two pseudocomponents: light and heavy fractions, which like the water component, can vaporize. Oil exhibits viscoplastic rheology, its filtration does not obey Darcy's classical linear law. Simulation considers not only the dependence of fluids density and viscosity on temperature, but also improvement of oil rheological properties with temperature increasing.

To solve this problem numerically we use streamline method with splitting by physical processes, which consists in separating the convective heat transfer directed along filtration from thermal conductivity and gravitation. The article proposes a new approach to streamline methods application, which allows correctly simulate nonlinear flow problems with temperature-dependent rheology. The core of this algorithm is to consider the integration process as a set of quasi-equilibrium states that are results of solving system on a global grid. Between these states system solved on a streamline grid. Usage of the streamline method allows not only to accelerate calculations, but also to obtain a physically reliable solution, since integration takes place on a grid that coincides with the fluid flow direction.

In addition to the streamline method, the paper presents an algorithm for nonsmooth coefficients accounting, which arise during simulation of viscoplastic oil flow. Applying this algorithm allows keeping sufficiently large time steps and does not change the physical structure of the solution.

Obtained results are compared with known analytical solutions, as well as with the results of commercial package simulation. The analysis of convergence tests on the number of streamlines, as well as on different streamlines grids, justifies the applicability of the proposed algorithm. In addition, the reduction of calculation time in comparison with traditional methods demonstrates practical significance of the approach.