All issues

The paper considers the problem of transverse impact on a thin preloaded fiber. The commonly accepted theory of transverse impact on a thin fiber is based on the classical works of Rakhmatulin and Smith. The simple relations obtained from the Rakhmatulin – Smith theory are widely used in engineering practice. However, there are numerous evidences that experimental results may differ significantly from estimations based on these relations. A brief overview of the factors that cause the differences is given in this article.

This paper focuses on the shear wave velocity, as it is the only feature that can be directly observed and measured using high-speed cameras or similar methods. The influence of the fiber preload on the wave speed is considered. This factor is important, since it inevitably arises in the experimental results. The reliable fastening and precise positioning of the fiber during the experiments requires its preload. This work shows that the preload significantly affects the shear wave velocity in the impacted fiber.

Numerical calculations were performed for Kevlar 29 and Spectra 1000 yarns. Shear wave velocities are obtained for different levels of initial tension. A direct comparison of numerical results and analytical estimations with experimental data is presented. The speed of the transverse wave in free and preloaded fibers differed by a factor of two for the setup parameters considered. This fact demonstrates that measurements based on high-speed imaging and analysis of the observed shear waves should take into account the preload of the fibers.

This paper proposes a formula for a quick estimation of the shear wave velocity in preloaded fibers. The formula is obtained from the basic relations of the Rakhmatulin – Smith theory under the assumption of a large initial deformation of the fiber. The formula can give significantly better results than the classical approximation, this fact is demonstrated using the data for preloaded Kevlar 29 and Spectra 1000. The paper also shows that direct numerical calculation has better corresponding with the experimental data than any of the considered analytical estimations.

Data hiding in digital images is a promising direction of cybersecurity. Digital steganography methods provide imperceptible transmission of secret data over an open communication channel. The information embedding efficiency depends on the embedding imperceptibility, capacity, and robustness. These quality criteria are mutually inverse, and the improvement of one indicator usually leads to the deterioration of the others. A balance between them can be achieved using metaheuristic optimization. Metaheuristics are a class of optimization algorithms that find an optimal, or close to an optimal solution for a variety of problems, including those that are difficult to formalize, by simulating various natural processes, for example, the evolution of species or the behavior of animals. In this study, we propose an approach to data hiding in the hybrid spatial-frequency domain of digital images based on metaheuristic optimization. Changing a block of image pixels according to some change matrix is considered as an embedding operation. We select the change matrix adaptively for each block using metaheuristic optimization algorithms. In this study, we compare the performance of three metaheuristics such as genetic algorithm, particle swarm optimization, and differential evolution to find the best change matrix. Experimental results showed that the proposed approach provides high imperceptibility of embedding, high capacity, and error-free extraction of embedded information. At the same time, storage of change matrices for each block is not required for further data extraction. This improves user experience and reduces the chance of an attacker discovering the steganographic attachment. Metaheuristics provided an increase in imperceptibility indicator, estimated by the PSNR metric, and the capacity of the previous algorithm for embedding information into the coefficients of the discrete cosine transform using the QIM method [Evsutin, Melman, Meshcheryakov, 2021] by 26.02% and 30.18%, respectively, for the genetic algorithm, 26.01% and 19.39% for particle swarm optimization, 27.30% and 28.73% for differential evolution.

The paper is devoted to one approach to constructing subgradient methods for strongly convex programming problems with several functional constraints. More precisely, the strongly convex minimization problem with several strongly convex (inequality-type) constraints is considered, and first-order optimization methods for this class of problems are proposed. The special feature of the proposed methods is the possibility of using the strong convexity parameters of the violated functional constraints at nonproductive iterations, in theoretical estimates of the quality of the produced solution by the methods. The main task, to solve the considered problem, is to propose a subgradient method with adaptive rules for selecting steps and stopping rule of the method. The key idea of the proposed methods in this paper is to combine two approaches: a scheme with switching on productive and nonproductive steps and recently proposed modifications of mirror descent for convex programming problems, allowing to ignore some of the functional constraints on nonproductive steps of the algorithms. In the paper, it was described a subgradient method with switching by productive and nonproductive steps for strongly convex programming problems in the case where the objective function and functional constraints satisfy the Lipschitz condition. An analog of the proposed subgradient method, a mirror descent scheme for problems with relatively Lipschitz and relatively strongly convex objective functions and constraints is also considered. For the proposed methods, it obtained theoretical estimates of the quality of the solution, they indicate the optimality of these methods from the point of view of lower oracle estimates. In addition, since in many problems, the operation of finding the exact subgradient vector is quite expensive, then for the class of problems under consideration, analogs of the mentioned above methods with the replacement of the usual subgradient of the objective function or functional constraints by the $\delta$-subgradient were investigated. The noted approach can save computational costs of the method by refusing to require the availability of the exact value of the subgradient at the current point. It is shown that the quality estimates of the solution change by $O(\delta)$. The results of numerical experiments illustrating the advantages of the proposed methods in comparison with some previously known ones are also presented.

The paper addresses the problem of modeling the formation and propagation of panic states in social groups with relatively stable structures of interpersonal interactions. Panic is interpreted as a nonlinear process of emotional contagion arising from the interaction between individual psychological characteristics and collective effects within a social environment. In contrast to models focused on the spatial dynamics of moving crowds, the proposed approach concentrates on quasi-stationary interaction networks that reflect informational and emotional contacts among individuals.

The developed discrete network dynamical system integrates individual temperament parameters (sanguine, choleric, phlegmatic, melancholic), the structure of social connections, and nonlinear mechanisms of collective behavior. The individual dynamics of panic are described using an S-shaped growth function, which ensures boundedness of the emotional arousal level and captures the stages of its formation and saturation. Social influence is modeled on a graph of interpersonal interactions (an Erdos –Renyi random network) through local contacts between individuals.

Additionally, the model incorporates the effects of collective contagion and avalanche-like amplification driven by the average panic level in the group, as well as a baseline stress factor depending on group size. Numerical simulation is implemented in a discrete iterative form, allowing for the analysis of both individual and group panic trajectories. A quantitative indicator of the panic propagation rate is introduced, defined by the time required for the group to reach a state close to full panic.

A comparative analysis of heterogeneous and homogeneous groups is conducted, demonstrating that group heterogeneity significantly accelerates panic propagation due to inter-temperament interactions: highly excitable individuals act as initiators of emotional contagion, while more stable individuals partially dampen its dynamics. The evaluation of the model quality using the coefficient of determination shows a high degree of consistency within the simulation data.

The practical significance of the work lies in the potential application of the model for analyzing the resilience of social groups to panic states, assessing risks at mass events, and developing intelligent systems for monitoring collective behavior. Future research directions include extending the model to account for directed and dynamic networks, as well as its calibration based on empirical data.

In neuroscience, the study of odor coding mechanisms requires the analysis of spatial activation patterns of olfactory structures (glomeruli) reconstructed from multiphoton microscopy data. However, the lack of a formal statistical framework for analyzing population-level summary maps limits result reproducibility and hinders the development of predictive models. To address these limitations, we developed a novel methodology for the analysis of olfactory activity maps aggregated across multiple animals, based on the theory of unmarked spatial point processes. The methodology includes a data preprocessing procedure and a numerical analysis algorithm implemented in the R environment using the spatstat package.

The proposed approach enables: (1) transformation of raw glomerular activity maps into point patterns while preserving information about glomerular sizes (replacing size information with local point density is a methodological compromise reflecting the “functional weight” of glomerular input); (2) analysis of point patterns based on spatial morphometric characteristics of domains — regions of stable glomerular activation in the olfactory bulb, each approximated by an ellipse, with ellipse parameters (center coordinates in stereotaxic space, major and minor axis lengths, orientation angles), areas, and intra-ellipse point densities reflecting odorant-specific response signatures; (3) statistical hypothesis testing for spatial randomness (Complete Spatial Randomness) using Ripley’s $K$-function, the nearest-neighbor G-function, and Monte Carlo simulations; (4) synthesis of a parametric pairwise interaction model (Strauss process), whose parameters $(r_{PI}, \gamma)$ have a clear biological interpretation — the spatial interaction scale of glomeruli and the strength of response comodulation, respectively.

The methodology was validated using experimental data obtained from 24 laboratory rats: 10 animals stimulated with camphor and 14 with methyl benzoate. The fitted Strauss models yielded close but odorant-specific parameters: interaction radii $r_{PI}$ of 150 $\mu$m (camphor) and 120 μm (methyl benzoate); interaction parameters $gamma$ of 0.95 and 0.89, respectively. The total domain areas (0.60 mm² and 0.73 mm²) and point densities (38 and 43 points/mm²) calculated at the first stage of analysis are fully consistent with the parametric signatures $(r_{PI}, \gamma)$ of the Strauss model. Model validation using $Q$-$Q$ plots of smoothed residuals confirmed their adequacy.

Our results are consistent with data previously obtained using genetic labeling and functional mapping techniques, demonstrating the correctness of the proposed methodology and the effectiveness of multiphoton laser scanning microscopy for such applications. The proposed framework provides reproducible quantitative assessment of glomerular domains within a unified stereotaxic coordinate system and can be extended to other odorants and biological species. All findings were obtained under anesthesia; extrapolation to active olfactory strategies in awake animals requires further investigation.

Modern big science projects are becoming highly data intensive to the point where offline processing of stored data is infeasible. High data throughput computing, or Data Stream Computing, for future projects is required to deal with terabytes of data per second which cannot be stored in long-term storage elements. Conventional data-centres based on typical server-grade hardware are expensive and are biased towards processing power. The overall I/O bandwidth can be increased with massive parallelism, usually at the expense of excessive processing power and high energy consumption. An ARM System on Chip (SoC) based processing unit may address the issue of system I/O and CPU balance, affordability and energy efficiency since ARM SoCs are mass produced and designed to be energy efficient for use in mobile devices. Such a processing unit is currently in development, with a design goal of 20 Gb/s I/O throughput and significant processing power. The I/O capabilities of consumer ARM System on Chips are discussed along with to-date performance and I/O throughput tests.

The grid-characteristic method is successfully used for solving hyperbolic systems of partial differential equations (for example, transport / acoustic / elastic equations). It allows to construct correctly algorithms on contact boundaries and boundaries of the integration domain, to a certain extent to take into account the physics of the problem (propagation of discontinuities along characteristic curves), and has the property of monotonicity, which is important for considered problems. In the cases of two-dimensional and three-dimensional problems the method makes use of a coordinate splitting technique, which enables us to solve the original equations by solving several one-dimensional ones consecutively. It is common to use up to 3-rd order one-dimensional schemes with simple splitting techniques which do not allow for the convergence order to be higher than two (with respect to time). Significant achievements in the operator splitting theory were done, the existence of higher-order schemes was proved. Its peculiarity is the need to perform a step in the opposite direction in time, which gives rise to difficulties, for example, for parabolic problems.

In this work coordinate splitting of the 3-rd and 4-th order were used for the two-dimensional hyperbolic problem of the linear elasticity. This made it possible to increase the final convergence order of the computational algorithm. The paper empirically estimates the convergence in L1 and L∞ norms using analytical solutions of the system with the sufficient degree of smoothness. To obtain objective results, we considered the cases of longitudinal and transverse plane waves propagating both along the diagonal of the computational cell and not along it. Numerical experiments demonstrated the improved accuracy and convergence order of constructed schemes. These improvements are achieved with the cost of three- or fourfold increase of the computational time (for the 3-rd and 4-th order respectively) and no additional memory requirements. The proposed improvement of the computational algorithm preserves the simplicity of its parallel implementation based on the spatial decomposition of the computational grid.

The possibility of numerical 3D simulation of thrombi formation is considered.

The developed up to now detailed mathematical models describing formation of thrombi and clots include a great number of equations. Being implemented in a CFD code, the detailed mathematical models require essential computer resources for simulation of the thrombi growth in a blood flow. A reasonable alternative way is using reduced mathematical models. Two models based on the reduced mathematical model for the thrombin generation are described in the given paper.

The first model describes growth of a thrombus in a great vessel (artery). The artery flows are essentially unsteady. They are characterized by pulse waves. The blood velocity here is high compared to that in the vein tree. The reduced model for the thrombin generation and the thrombus growth in an artery is relatively simple. The processes accompanying the thrombin generation in arteries are well described by the zero-order approximation.

A vein flow is characterized lower velocity value, lower gradients, and lower shear stresses. In order to simulate the thrombin generation in veins, a more complex system of equations has to be solved. The model must allow for all the non-linear terms in the right-hand sides of the equations.

The simulation is carried out in the industrial software FlowVision.

The performed numerical investigations have shown the suitability of the reduced models for simulation of thrombin generation and thrombus growth. The calculations demonstrate formation of the recirculation zone behind a thrombus. The concentration of thrombin and the mass fraction of activated platelets are maximum here. Formation of such a zone causes slow growth of the thrombus downstream. At the upwind part of the thrombus, the concentration of activated platelets is low, and the upstream thrombus growth is negligible.

When the blood flow variation during a hart cycle is taken into account, the thrombus growth proceeds substantially slower compared to the results obtained under the assumption of constant (averaged over a hard cycle) conditions. Thrombin and activated platelets produced during diastole are quickly carried away by the blood flow during systole. Account of non-Newtonian rheology of blood noticeably affects the results.

Accurate tree identification is essential for ecological monitoring, biodiversity assessment, and forest management. Traditional manual survey methods are labor-intensive and ineffective over large areas. Advances in remote sensing technologies including lidar and hyperspectral imaging improve automated, exact detection in many fields.

Nevertheless, these technologies typically require extensive labeled data and manual feature engineering, which restrict scalability. This research proposes a new method of Self-Supervised Learning (SSL) with the SimCLR framework to enhance the classification of tree species using unlabelled data. SSL model automatically discovers strong features by merging the spectral data from hyperspectral data with the structural data from LiDAR, eliminating the need for manual intervention.

We evaluate the performance of the SSL model against traditional classifiers, including Random Forest (RF), Support Vector Machines (SVM), and Supervised Learning methods, using a dataset from the ECODSE competition, which comprises both labeled and unlabeled samples of tree species in Florida’s Ordway-Swisher Biological Station. The SSL method has been demonstrated to be significantly more effective than traditional methods, with a validation accuracy of 97.5% compared to 95.56% for Semi-SSL and 95.03% for CNN in Supervised Learning.

Subsampling experiments showed that the SSL technique is still effective with less labeled data, with the model achieving good accuracy even with only 20% labeled data points. This conclusion demonstrates SSL’s practical applications in circumstances with insufficient labeled data, such as large-scale forest monitoring.

This study presents a methodology for assessing the functioning of complex systems, taking into account the type of distribution of indicators characterizing the functioning of structural elements of such a system operating under conditions of uncertainty. Unlike previous studies, the work integrates the identification of the type of indicator distribution with their Bayesian assessment, taking into account the norms characterizing the required results of the functioning of the structural elements of the system. The type of distribution and its characteristics provide more complete information about the properties of an object and their consideration affects the results of evaluating the functioning of elements of complex systems, especially in cases of the presence of “heavy” tails characteristic of a number of socio-economic processes and systems. It is shown that it is advisable to identify the type of distribution based on modified data due to the exclusion of the best trend in statistical characteristics. The determination of the best type of distribution is carried out according to the Kolmogorov – Smirnov agreement criterion, which showed the best (according to the available sample) statistical estimates compared to other criteria or a mixture of them. The obtained type of distribution is used in the probabilistic assessment of the results of the functioning of subsystem elements based on Bayesian intelligent technologies that successfully operate in conditions of uncertainty, and which make it possible to present such results on numerical and linguistic scales in a general hierarchical information model. The methodology was tested using the example of the object subsystem (G.B.Kleiner’s spatio-temporal classification) of the economic subsystem of the Tula region, considered as a complex system — a socio-ecological-economic system. The volume of gross domestic product by region in six sections of the all-Russian classifier of economic activities (sections A, B, C, D, E) was used as assessment indicators. In some cases, it is possible to reduce the level of uncertainty in the estimates of indicators.; to obtain estimates that are more stringent than the norm, which ultimately leads to the conclusion that the use of the distribution type in the formation of probabilistic estimates of indicators of structural elements of complex systems makes it possible to justify their correct application within the framework of the concept of evidence-based modeling.