All issues

The article presents the intermediate results of the development of a control system for a remotely piloted agricultural aircraft (RPAA). The concept of using an automated complex for performing aerochemical work (ACW) designed for processing fields, water areas, forests with the purpose of protection from pests of plants, fertilization is developed. The basic component of the complex is a manned agricultural aircraft MV-500 developed by LLC “Firm “MVEN” (Kazan). The use of the aircraft in unmanned mode will provide an increase in the productivity of the aircraft, will increase the payload.

The article defines the composition of the complex for automation of ACW: aircraft, ground control center, onboard equipment for automated control of the aircraft and the formation of a map of the heights of the section being processed, and the satellite precise positioning system necessary to automate the control of the aircraft. The aircraft is equipped with an automated control system that provides remote control of take-off and landing and automatic control of the flight trajectory at extremely low altitude when performing ACW and performing spatial turns at the boundaries of the treated areas. It is proposed to take off, landing, dropping an aircraft into the ACW exercise area by means of a pilot operator from a ground control station. The ground control point should provide reception and display on the operator's screen of flight information and several types from the aircraft. The operator can control alternately several aircraft during these phases of flight with the help of ground control authorities. In the future, it is planned to automate these stages of flight, leaving behind the pilot-operator control functions and remote control capabilities in special cases. For the navigation of the aircraft, when performing ACW on board, RTK (Real Time Kinematic) equipment is installed, providing a measurement with centimeter accuracy of coordinates and aircraft heights relative to the base station installed in the ground control station. Before the implementation of ACW, a three-dimensional digital map of the processed area is built by adding existing cadastral maps with measurements of the elevations of the section carried out with the help of on-board radio and optical altimeters of the same aircraft.

To date, the following system components have been manufactured and tested: a remotely controlled model of the MV-500 aircraft at a scale of 1:5, a satellite positioning system; system for obtaining images and telemetry information from the board model; autopilot; methods of obtaining three-dimensional digital maps of sections and planning flight trajectories for ACW.

While modeling seismic wave propagation, it is important to take into account nontrivial topography, as this topography causes multiple complex phenomena, such as diffraction at rough surfaces, complex propagation of Rayleigh waves, and side effects caused by wave interference. The primary goal of this research is to construct a method that implements the free surface on topography, utilizing an overset curved grid for characterization, while keeping the main grid structured rectangular. For a combination of the regular and curve-linear grid, the workability of the grid characteristics method using overset grids (also known as the Chimera grid approach) is analyzed. One of the benefits of this approach is computational complexity reduction, caused by the fact that simulation in a regular, homogeneous physical area using a sparse regular rectangle grid is simpler. The simplification of the mesh building mechanism (one grid is regular, and the other can be automatically built using surface data) is a side effect. Despite its simplicity, the method we propose allows us to increase the digitalization of fractured regions and minimize the Courant number. This paper contains various comparisons of modeling results produced by the proposed method-based solver, and results produced by the well-known solver specfem2d, as well as previous modeling results for the same problems. The drawback of the method is that an interpolation error can worsen an overall model accuracy and reduce the computational schema order. Some countermeasures against it are described. For this paper, only two-dimensional models are analyzed. However, the method we propose can be applied to the three-dimensional problems with minimal adaptation required.

In this paper, we investigate different alternative ideas for the design of digital predistortion models for radiofrequency power amplifiers. When compared to the greedy search algorithm, these algorithms allow a faster identification of the model parameters combination while still performing reasonably well. For the subsequent implementation, different metrics of model costs and score results in the process of optimization enable us to achieve sparse selections of the model, which balance the model accuracy and model resources (according to the complexity of implementation). The results achieved in the process of simulations show that combinations obtained with explored algorithms show the best performance after a lower number of simulations.

The paper investigates a potential solution to the problem of Self-Interference Cancellation (SIC) encountered in the design of In-Band Full-Duplex (IBFD) communication systems. The suppression of selfinterference is implemented in the digital domain using multilayer nonlinear models adapted via the gradient descent method. The presence of local optima and saddle points in the adaptation of multilayer models prevents the use of second-order methods due to the indefinite nature of the Hessian matrix.

This work proposes the use of the Mixed Newton Method (MNM), which incorporates information about the second-order mixed partial derivatives of the loss function, thereby enabling a faster convergence rate compared to traditional first-order methods. By constructing the Hessian matrix solely with mixed second-order partial derivatives, this approach mitigates the issue of “getting stuck” at saddle points when applying the Mixed Newton Method for adapting multilayer nonlinear self-interference compensators in full-duplex system design.

The Hammerstein model with complex parameters has been selected to represent nonlinear selfinterference. This choice is motivated by the model’s ability to accurately describe the underlying physical properties of self-interference formation. Due to the holomorphic property of the model output, the Mixed Newton Method provides a “repulsion” effect from saddle points in the loss landscape.

The paper presents convergence curves for the adaptation of the Hammerstein model using both the Mixed Newton Method and conventional gradient descent-based approaches. Additionally, it provides a derivation of the proposed method along with an assessment of its computational complexity.

This study develops a previously proposed Method of Computer Analogy (MCA) based on formalization of digital computer operations. The paper discusses the position of the proposed approach among other well-known methods. It is emphasized that the primary objective is to derive analytical solutions, although in some cases they have to resort to semianalytical approximations. The paper focuses on constructing solutions for systems which, for certain parameter values, demonstrate the deterministic chaos behavior, namely Lorenz, Marioka – Shimitsu and R¨ossler systems. The paper also considers obtaining solution for Van der Pol equation (reduced to a nonlinear system). The aim of the study is to construct semi-analytical solutions represented as a segment of a power series in a step size of approximating difference scheme. To prevent overflow, authors formalize rank transfer operation. The authors apply a convergent difference scheme, referred to as the “guiding” scheme, to advance to the next step of the independent variable. The resulting approximation by a sum with only a few terms provides an approximation to the solution with any accuracy in accordance with the accuracy of the governing difference scheme. The senior digits in the resulting approximation exhibit probabilistic properties that can be modeled by known distributions, thereby enabling the derivation of analytical and semi-analytical approximations. The paper presents linear approximations that are the base for a complete approximations of solutions and provide important qualitative as well as some quantitative properties of solutions of considered systems. This work describes approximations of various orders, including those that do not guarantee convergence to the exact solution, but simplify the analysis of certain properties of nonlinear equations and systems. In particular, for the Van der Pol equation, authors demonstrate that its corresponding system has a cyclic solution and provide an estimate of its scale. A modification of the MCA that has features of the Monte Carlo method makes it possible to remove recurrent sequences and construct complete solutions in simple situations. The authors mention a promising approach for representing the solution using branched continued fractions.

Modern approach to modernization of the experimental techniques involves design of mathematical models of the wind-tunnel, which are also referred to as Electronic of Digital Wind-Tunnels. They are meant to supplement experimental data with computational analysis. Using Electronic Wind-Tunnels is supposed to provide accurate information on aerodynamic performance of an aircraft basing on a set of experimental data, to obtain agreement between data from different test facilities and perform comparison between computational results for flight conditions and data with the presence of support system and test section.

Completing this task requires some preliminary research, which involves extensive wind-tunnel testing as well as RANS-based computational research with the use of supercomputer technologies. At different stages of computational investigation one may have to model not only the aircraft itself but also the wind-tunnel test section and the model support system. Modelling such complex geometries will inevitably result in quite complex vertical and separated flows one will have to simulate. Another problem is that boundary layer transition is often present in wind-tunnel testing due to quite small model scales and therefore low Reynolds numbers.

In the current article the first stage of the Electronic Wind-Tunnel design program is covered. This stage involves computational investigation of aerodynamic characteristics of the generic flying-wing UAV model previously tested in TsAGI T-102 wind-tunnel. Since this stage is preliminary the model was simulated without taking test-section and support system geometry into account. The boundary layer was considered to be fully turbulent.

For the current research FlowVision computational code was used because of its automatic grid generation feature and stability of the solver when simulating complex flows. A two-equation k–ε turbulence model was used with special wall functions designed to properly capture flow separation. Computed lift force and drag force coefficients for different angles-of-attack were compared to the experimental data.

Image denoising is one of the fundamental problems in digital image processing. This problem usually refers to the reconstruction of an image from an observed image degraded by noise. There are many factors that cause this degradation such as transceiver equipment, or environmental influences, etc. In order to obtain higher quality images, many methods have been proposed for image denoising problem. Most image denoising method are based on total variation (TV) regularization to develop efficient algorithms for solving the related optimization problem. TV-based models have become a standard technique in image restoration with the ability to preserve image sharpness.

In this paper, we focus on Poisson noise usually appearing in photon-counting devices. We propose an effective regularization model based on combination of first-order and fractional-order total variation for image reconstruction corrupted by Poisson noise. The proposed model allows us to eliminate noise while edge preserving. An efficient alternating minimization algorithm is employed to solve the optimization problem. Finally, provided numerical results show that our proposed model can preserve more details and get higher image visual quality than recent state-of-the-art methods.

The article considers the mathematical aspects of the problem of identifying a multicomponent scattering medium based on pulsed multienergy X-ray irradiation data. X-ray diagnostics problems are of considerable interest from both theoretical and practical points of view, and radiographic methods are indispensable in non-destructive testing of products.

Within the framework of a mathematical model based on a non-stationary integro-differential equation of radiation transfer, the inverse problem of finding the attenuation coefficient for radiation known at the boundary of the region and the problem of identifying a substance based on the found values of the attenuation coefficient on a discrete set of irradiation energies of the medium are formulated.

A preliminary processing of a wide list of substances of interest in computed tomography was carried out to determine the possibility of their identification by an approximately specified radiation attenuation coefficient characterizing the medium. When analyzing the degree of proximity of substances in a certain norm, it was found that the set of all possible substances potentially contained in the medium is divided into a finite number of non-intersecting clusters. For a sufficiently short duration of the probing signal, the scattering component of the radiation leaving the medium is asymptotically small. This circumstance allows us to reduce the inverse problem for the radiation transfer equation to the problem of inverting the Radon transform from the attenuation coefficient. The possibility of unambiguous or partial identification of a substance by varying the duration of the probing pulse and the number of energy levels of irradiation of the medium is analyzed using numerical modeling methods on a specially developed digital phantom.

The program for automatic revealing of threshold values for characterizing physiological state of vessels and detection of early stages of retina pathology is offered. The algorithm is based on checking character of crossing sites of vessel images with the "mask" consisting of concentric circumferences (the first circumference is imposed directly on the sclera capsules of an optic nerve disk). The new method allows revealing of a network of blood vessels and flanking zones and detection of initial stage of pathological changes in a retina by digital images.

A model of biogeochemical cycles for nutrient transformation in the ecosystem of a water body has been developed using the example of the Lake Teletskoye (TL) to assess its assimilation potential in the absence of direct measurements for total nitrogen and phosphorus concentrations, instead of which the corresponding simulated data. The validity is justified by checking the adequacy of the simulation results to the data of average monthly long-term observations for all variables of the state for model. The model was calibrated with taking into account data from observations of water quality in 1985–2003, as well as a scenario version of the hydrological regime in 2016. The analysis of the intra-annual changeability of state variables, nitrogen and phosphorus inputs and outputs in TL water is given. The preliminary values of the permissible load N and P on the lake is accessed. The model analysis showed that the lake has practically no assimilation potential with respect to phosphorus compounds. The corresponding values of concentrations are equal to: P_tot. = 0.013 gP/m³, which is equal to the average annual content over the period of 18-year observations. The threshold content of N_tot. = 0.895 gN/m³. The assimilation potential for nitrogen is small, within the second significant digit after the decimal point, bearing in mind that its simulated average annual value is 0.836 gN/m³. The results of simulation indicate that the TL waters, due to the low water temperatures, along with their unique purity, differ in an extremely poorly developed community of hydrobionts. In the case of other lakes, the increase of anthropogenic pressure could be mitigated by utilization due to the vital activity of sufficiently developed hydrobionts communities. Here, there is no sufficient self-purification resource, and a relatively small increase in anthropogenic load can lead to a violation of the sustainability.