All issues

A correct model of lipid molecule (distearoylphosphatidylcholine, DSPC) and lipid membrane in water was constructed. Model lipid membrane is stable and has a reliable energy distribution among degrees of freedom. Also after equilibration model system has spatial parameters very similar to those of real DSPC membrane in liquid-crystalline phase. This model was used for studying of lipid membrane permeability to oxygen and water molecules and sodium ion. We obtained the values for transmembrane mobility and diffusion coefficients profiles, which we used for effective permeability coefficients calculation. We found lipid membranes to have significant diffusional resistance to penetration not only by charged particles, such as ions, but also by nonpolar molecules, such as oxygen molecule. We propose theoretical approach for calculation of particle flow across a membrane, as well as methods for estimation of distribution coefficients between bilayer and water phase.

The article is dedicated to mathematic modeling of natural water desalination process by method of thermal distillation. The article gives the equations which allow describing the processes of film flowing and boiling of water, steam condensation and vacuum maintenance. The article presents the algorithm of calculation, implemented in MatLab computer mathematic system and Excel electronic tables, and the initial data required for the calculation. The model has been checked for adequacy. The calculation of ten-effect distillation system is given. The results of work can be used in design and optimization of process conditions for distillation systems.

The paper considers models of platelet thrombus formation in blood plasma flow in a cylindrical vessel, based on the “advection–diffusion” equation and the Fokker–Planck equation. The comparison of the results of calculations based on these models is given. Considered models show qualitatively similar behavior at the initial stage of thrombus formation. А detailed investigation of large clots requires models’ improvement.

In the present paper, we discuss the possibility of a simplified three-dimensional unsteady simulation of plasma-assisted combustion of gaseous fuel in a supersonic airflow. Simulation was performed by using FlowVision CFD software. Analysis of experimental geometry show that it has essentially 3D nature that conditioned by the discrete fuel injection into the flow as well as by the presence of the localized plasma filaments. Study proposes a variant of modeling geometry simplification based on symmetry of the aerodynamic duct and periodicity of the spatial inhomogeneities. Testing of modified FlowVision $k–\varepsilon$ turbulence model named «KEFV» was performed for supersonic flow conditions. Based on that detailed grid without wall functions was used the field of heat and near fuel injection area and surfaces remote from the key area was modeled with using of wall functions, that allowed us to significantly reduce the number of cells of the computational grid. Two steps significantly simplified a complex problem of the hydrocarbon fuel ignition by means of plasma generation. First, plasma formations were simulated by volumetric heat sources and secondly, fuel combustion is reduced to one brutto reaction. Calibration and parametric optimization of the fuel injection into the supersonic flow for IADT-50 JIHT RAS wind tunnel is made by means of simulation using FlowVision CFD software. Study demonstrates a rather good agreement between the experimental schlieren photo of the flow with fuel injection and synthetical one. Modeling of the flow with fuel injection and plasma generation for the facility T131 TSAGI combustion chamber geometry demonstrates a combustion mode for the set of experimental parameters. Study emphasizes the importance of the computational mesh adaptation and spatial resolution increasing for the volumetric heat sources that model electric discharge area. A reasonable qualitative agreement between experimental pressure distribution and modeling one confirms the possibility of limited application of such simplified modeling for the combustion in high-speed flow.

The purpose of research was to develop a mathematical model for pulsating blood flow in the part of aorta with their branches. Since the deformation of this most solid part of the aorta is small during the passage of the pulse wave, the blood vessels were considered as non-deformable curved cylinders. The article describes the internal structure of blood and some internal structural effects. This analysis shows that the blood, which is essentially a suspension, can only be regarded as a non-Newtonian fluid. In addition, the blood can be considered as a liquid only in the blood vessels, diameter of which is much higher than the characteristic size of blood cells and their aggregate formations. As a non-Newtonian fluid the viscous liquid with the power law of the relationship of stress with shift velocity was chosen. This law can describe the behaviour not only of liquids but also dispersions. When setting the boundary conditions at the entrance into aorta, reflecting the pulsating nature of the flow of blood, it was decided not to restrict the assignment of the total blood flow, which makes no assumptions about the spatial velocity distribution in a cross section. In this regard, it was proposed to model the surface envelope of this spatial distribution by a part of a paraboloid of rotation with a fixed base radius and height, which varies in time from zero to maximum speed value. The special attention was paid to the interaction of blood with the walls of the vessels. Having regard to the nature of this interaction, the so-called semi-slip condition was formulated as the boundary condition. At the outer ends of the aorta and its branches the amounts of pressure were given. To perform calculations the tetrahedral computer network for geometric model of the aorta with branches has been built. The total number of meshes is 9810. The calculations were performed with use of the software package ABACUS, which has also powerful tools for creating geometry of the model and visualization of calculations. The result is a distribution of velocities and pressure at each time step. In areas of branching vessels was discovered temporary presence of eddies and reverse currents. They were born via 0.47 s from the beginning of the pulse cycle and disappeared after 0.14 s.

The paper presents a physico-mathematical model of the perturbed region formed in the lower D-layer of the ionosphere under the action of directed radio emission flux from a terrestrial stand of the megahertz frequency range, obtained as a result of comprehensive theoretical studies. The model is based on the consideration of a wide range of kinetic processes taking into account their nonequilibrium and in the two-temperature approximation for describing the transformation of the radio beam energy absorbed by electrons. The initial data on radio emission achieved by the most powerful radio-heating stands are taken in the paper. Their basic characteristics and principles of functioning, and features of the altitude distribution of the absorbed electromagnetic energy of the radio beam are briefly described. The paper presents the decisive role of the D-layer of the ionosphere in the absorption of the energy of the radio beam. On the basis of theoretical analysis, analytical expressions are obtained for the contribution of various inelastic processes to the distribution of the absorbed energy, which makes it possible to correctly describe the contribution of each of the processes considered. The work considers more than 60 components. The change of the component concentration describe about 160 reactions. All the reactions are divided into five groups according to their physical content: ionization-chemical block, excitation block of metastable electronic states, cluster block, excitation block of vibrational states and block of impurities. Blocks are interrelated and can be calculated both jointly and separately. The paper presents the behavior of the parameters of the perturbed region in daytime and nighttime conditions is significantly different at the same radio flux density: under day conditions, the maximum electron concentration and temperature are at an altitude of ~45–55 km; in night ~80 km, with the temperature of heavy particles rapidly increasing, which leads to the occurrence of a gas-dynamic flow. Therefore, a special numerical algorithm are developed to solve two basic problems: kinetic and gas dynamic. Based on the altitude and temporal behavior of concentrations and temperatures, the algorithm makes it possible to determine the ionization and emission of the ionosphere in the visible and infrared spectral range, which makes it possible to evaluate the influence of the perturbed region on radio engineering and optoelectronic devices used in space technology.

The review is based on some of the authors ’early works of particular scientific, methodological and practical interest and the greatest attention is paid to recent works, where quite detailed numerical studies of not only single, but also double and multiple explosions in a wide range of heights and environmental conditions have been performed . Since the shock wave of a powerful explosion is one of the main damaging factors in the lower atmosphere, the review focuses on both the physical analysis of their propagation and their interaction. Using the three-dimensional algorithms developed by the authors, the effects of interference and diffraction of several shock waves, which are interesting from a physical point of view, in the absence and presence of an underlying surface of various structures are considered. Quantitative characteristics are determined in the region of their maximum values, which is of known practical interest. For explosions in a dense atmosphere, some new analytical solutions based on the small perturbation method have been found that are convenient for approximate calculations. For a number of conditions, the possibility of using the self-similar properties of equations of the first and second kind to solve problems on the development of an explosion has been shown.

Based on numerical analysis, a fundamental change in the structure of the development of the perturbed region with a change in the height of the explosion in the range of 100–120 km is shown. At altitudes of more than 120 km, the geomagnetic field begins to influence the development of the explosion; therefore, even for a single explosion, the picture of the plasma flow after a few seconds becomes substantially three-dimensional. For the calculation of explosions at altitudes of 120–1000 km under the guidance of academician A. Kholodov. A special three-dimensional numerical algorithm based on the MHD approximation was developed. Numerous calculations were performed and for the first time a quite detailed picture of the three-dimensional flow of the explosion plasma was obtained with the formation of an upward jet in 5–10 s directed in the meridional plane approximately along the geomagnetic field. After some modification, this algorithm was used to calculate double explosions in the ionosphere, spaced a certain distance. The interaction between them was carried out both by plasma flows and through a geomagnetic field. Some results are given in this review and are described in detail in the original articles.

In this paper a fluid flow between two close located rough surfaces depending on their location and discontinuity in contact areas is investigated. The area between surfaces is considered as the porous layer with the variable permeability, depending on roughness and closure of surfaces. For obtaining closure-permeability function, the flow on the small region of surfaces (100 $\mu$m) is modeled, for which the surfaces roughness profile created by fractal function of Weierstrass – Mandelbrot. The 3D-domain for this calculation fill out the area between valleys and peaks of two surfaces, located at some distance from each other. If the surfaces get closer, a contacts between roughness peaks will appears and it leads to the local discontinuities in the domain. For the assumed surfaces closure and boundary conditions the mass flow and pressure drop is calculated and based on that, permeability of the equivalent porous layer is evaluated.The calculation results of permeability obtained for set of surfaces closure were approximated by a polynom. This allows us to calculate the actual flow parameters in a thin layer of variable thickness, the length of which is much larger than the scale of the surface roughness. As an example, showing the application of this technique, flow in the gap between the billet and conical die in 3D-formulation is modeled. In this problem the permeability of an equivalent porous layer calculated for the condition of a linear decreased gap.

A cluster method of mathematical modeling of interval-stochastic thermal processes in complex electronic systems (ES), is developed. In the cluster method, the construction of a complex ES is represented in the form of a thermal model, which is a system of clusters, each of which contains a core that combines the heat-generating elements falling into a given cluster, the cluster shell and a medium flow through the cluster. The state of the thermal process in each cluster and every moment of time is characterized by three interval-stochastic state variables, namely, the temperatures of the core, shell, and medium flow. The elements of each cluster, namely, the core, shell, and medium flow, are in thermal interaction between themselves and elements of neighboring clusters. In contrast to existing methods, the cluster method allows you to simulate thermal processes in complex ESs, taking into account the uneven distribution of temperature in the medium flow pumped into the ES, the conjugate nature of heat exchange between the medium flow in the ES, core and shells of clusters, and the intervalstochastic nature of thermal processes in the ES, caused by statistical technological variation in the manufacture and installation of electronic elements in ES and random fluctuations in the thermal parameters of the environment. The mathematical model describing the state of thermal processes in a cluster thermal model is a system of interval-stochastic matrix-block equations with matrix and vector blocks corresponding to the clusters of the thermal model. The solution to the interval-stochastic equations are statistical measures of the state variables of thermal processes in clusters - mathematical expectations, covariances between state variables and variance. The methodology for applying the cluster method is shown on the example of a real ES.

Automated urban traffic monitoring systems are widely used to solve various tasks in intelligent transport systems of different regions. They include video enforcement, video surveillance, traffic management system, etc. Effective traffic management and rapid response to traffic incidents require continuous monitoring and analysis of information from these complexes, as well as time series forecasting for further anomaly detection in traffic flow. To increase the forecasting quality, data fusion from different sources is needed. It will reduce the forecasting error, related to possible incorrect values and data gaps. We implemented the approach for short-term and middle-term forecasting of traffic flow (5, 10, 15 min) based on data fusion from video enforcement and video surveillance systems. We made forecasting using different recurrent neural network architectures: LSTM, GRU, and bidirectional LSTM with one and two layers. We investigated the forecasting quality of bidirectional LSTM with 64 and 128 neurons in hidden layers. The input window size (1, 4, 12, 24, 48) was investigated. The RMSE value was used as a forecasting error. We got minimum RMSE = 0.032405 for basic LSTM with 64 neurons in the hidden layer and window size = 24.